(B) Left hand |
|
top fixture |
|
assembly |
|
Long stem |
|
track roller |
|
| (3) 1/4” - 14 x 1” |
Top fixture | Lag screws |
slide(s) |
|
8 | Strutting For Top Section |
Tools: Power drill, 7/16” Socket driver |
Note: Refer to Door Section Identification / Parts Breakdown.
Lay a short strut onto the top rail of the top section. Position the top of the strut 3/4” down from the top edge of the top section. Center the short strut from side to side on the section surface.
Drill pilot holes, 1” deep into the top section with a 1/8” drill bit.
IMPORTANT: Be extremely careful not to drill thru the section. Only drill 1” deep.
Attach the strut using (1) 1/4” - 14 x 1” lag screw at each predrilled hole.
Short strut |
Top section |
3/4” |
Typical |
top fixture |
assembly |
1/4” - 14 x 1” |
Lag screws |
9 | Bottom Section |
Tools: Level, Wooden shims (if necessary) |
Center the bottom section in the door opening. Level the section using wooden shims (if necessary) under the bottom section.
Weather seal |
Level |
Bottom section |
Wooden shims |
(If necessary) |
10 | Vertical Tracks |
Tools: Power Drill, 3/16” Drill bit, 7/16” Socket driver, Tape measure, |
IMPORTANT: If your door is to be installed prior to a finishing construction of the building’s floor, the vertical tracks and the door bottom section assembly should be installed such that when the floor is constructed, no door or track parts are trapped in the floor construction.
Important: The tops of the vertical tracks must be level from side to side.
If the bottom section was shimmed to level it, the vertical track on the shimmed side must be raised the height of the shim.
Position the left hand vertical track assembly / wall angle track assembly over the track rollers of the bottom section. Make sure the counterbalance lift cable is located between the track rollers and the door jamb. Drill 3/16” pilot holes into the door jamb for the lag screws.
For flag angle track assemblies:
Loosely fasten jamb brackets and flag angle to the jamb using 5/16” x
For wall angle track assembly:
Loosely fasten wall angle to the jamb using 5/16” x
If you have 2” vertical tracks:
Tighten lag screws, securing the bottom jamb bracket/bottom slot to jamb, maintain 3/8” to 5/8” spacing, between the bottom section and vertical track.
If you have 3” vertical tracks:
Tighten lag screws, securing the bottom jamb bracket/bottom slot to jamb, maintain 1/2” to 3/4” spacing, between the bottom section and vertical track.
Hang counterbalance lift cable over flag angle/wall angle. Repeat same process for other side.
Wallangle | Riveted track |
|
|
|
track |
|
|
| |
assembly | flag angle |
|
|
|
| shown |
|
|
|
|
|
| Lag |
|
|
|
| screw |
|
|
|
| locations |
|
| 5/16” x |
|
|
|
| Lag screws |
|
|
|
| Jamb |
|
|
|
| bracket | Flag | Fully Adjustable | Riveted |
|
| |||
|
| angle | flag angle | flag angle |
| Bottom | 2” Vertical track | Bottom | |
| section | |||
| spacing (3/8” to 5/8”) | section | ||
|
| |||
| Track | 3” Vertical track |
| |
| spacing (1/2” to 3/4”) |
| ||
| rollers |
| ||
|
|
|
| |
| Vertical track | Floor |
| Track roller |
|
|
|
| |
| assembly |
|
|
|
11 | Stacking Sections |
|
| |
Tools: Power drill,7/16” Socket driver |
|
|
Note: Make sure graduated end and center hinges are flipped down, when stacking another section on top.
NOTE: Larger doors will use long stem track rollers / long stem tandem rollers with double graduated end hinges.
Place track rollers and or tandem rollers into graduated end hinges of remaining sections.
With assistance, lift intermediate I (second) section and guide the track rollers / tandem rollers into the vertical tracks. Lower section until it is seated against bottom section. Keep sections aligned. Repeat same process for other sections, except top section.
NOTE: Refer to Graduated End Hinge And Strut Identification, to determine if your doors requires strutting, prior to attaching sections.
NOTE: Follow the typical practice, as shown in Steps Strutting and Step Half Center Hinges prior to installing the long struts and hinges to the lower rail of section(s).
NOTE: If no strutting is require on the lower rail of section, then follow instructions below. Graduated end hinges:
Starting with the outer graduated end hinges, flip the upper hinge leaf up and use it as a template. Mark and
NOTE: If you have double graduated end hinges, flip the inner upper hinge leaf up and use it as a template. Mark and
Center Hinge(s) and or half center hinge(s):
Starting with the center hinge, flip the upper hinge leaf up and use it as a template. Mark and
IMPORTANT: Be extremely careful not to drill thru the section. Only drill 1”
9
Please Do Not Return This Product To The Store. Contact your local
refer to your local yellow pages business listings or go to the Find a Dealer section online at