CABLE ASSEMBLY
36. Slide a 5/16” Flat Washer (8) onto a 5/16” x | 36 |
|
|
|
|
2 3/4” Bolt (11). Insert the Bolt through the indi- |
|
|
|
| |
|
|
|
|
| |
cated hole in the Pivot Arm (101). The Bolt |
|
|
|
|
|
must be inserted from the side shown. |
|
|
|
|
|
Fully tighten a 5/16” Nylon Jam Nut (93) onto | 21 |
|
|
|
|
the Bolt. |
| 93 |
|
|
|
Wrap the Military Press Cable (72) around a |
| 9 |
|
|
|
3 1/2” Pulley (15). Attach the Pulley and a |
|
|
|
| |
|
|
|
|
| |
Cable Trap (66) to the Pivot Arm (101) with |
|
|
|
|
|
the 3/8” x 3 3/4” Bolt (88), a 3/8” Flat Washer |
|
| 8 |
|
|
(9), and a 3/8” Nylon Locknut (21). Be sure |
| 101 | 11 |
| |
|
|
| |||
that the Pulley is on the side shown and |
|
|
| ||
|
|
|
|
| |
that the Cable Trap is positioned to hold |
| 72 |
|
|
|
the Cable in place. |
|
|
|
| |
| 15 |
|
|
| |
|
| 66 | 88 |
| |
|
|
|
| ||
|
|
|
|
| |
37. See inset drawing A. Attach a 3 1/2” Pulley | 37 |
|
|
|
|
(15) and a Cable Trap (66) to the upper hole |
|
| 15 | A | |
|
|
| |||
in a Long |
|
|
|
|
|
Bolt (12) and a 3/8” Nylon Locknut (21). Be |
| 21 |
|
| 66 |
sure that the Cable Trap is inside the Long |
|
|
| ||
|
|
|
|
| |
|
|
|
|
| |
assembled.) |
| 57 |
| 12 | |
Route the Military Press Cable (72) through |
|
| |||
|
|
|
|
| |
the Long |
|
|
|
| B |
Pulley (15). Be sure that the Cable is in the |
| 93 |
|
| |
groove of the Pulley and that the Cable |
|
|
|
| |
|
|
|
|
| |
and Pulley move smoothly. |
| 72 |
|
|
|
|
|
|
|
| |
See inset drawing B. Slide the end of the |
| 11 |
|
|
|
Military Press Cable (72) onto the end of the | 15 | 57 |
|
|
|
5/16” x 2 3/4 Bolt (11). Thread another 5/16” |
|
|
|
|
|
Nylon Jam Nut (93) onto the Bolt. Do not | 72 |
|
|
|
|
fully tighten the second Jam Nut. There |
|
|
|
| |
|
|
|
|
| |
must be room between the two Jam Nuts |
|
|
|
|
|
for the end of the Cable to pivot. |
|
|
|
|
|
17
