CABLE ASSEMBLY
38. Locate the Leg Press Cable (99). Attach the | 38 |
|
|
end of the Leg Press Cable to the Long “U”- |
|
| |
| 2 |
| |
Bracket (57) with a 1/4” Nylon Locknut (2) and |
|
| |
a 1/4” Flat Washer (10). Do not completely |
|
|
|
tighten the Nylon Locknut. It should be |
|
|
|
threaded onto the end of the Cable only a |
|
| 57 |
couple of turns, as shown in the inset |
|
|
|
drawing. |
| 10 |
|
|
|
| |
Wrap the Leg Press Cable (99) around a |
|
|
|
3 1/2” Pulley (15). Attach the Pulley to the Leg |
|
|
|
Press Upright (56) with the 3/8” x 3 3/4” Bolt |
| 99 |
|
(88), a 3/8” Flat Washer (9), and a 3/8” Nylon |
| 56 | |
Locknut (21). The ball on the Cable must be |
|
| |
|
|
| |
on the indicated side of the Pulley. Be sure |
| 88 | Ball |
that the Cable and Pulley move smoothly |
| 15 | |
and that the Cable is between the Pulley |
|
| |
|
|
| |
and the welded rod. |
|
|
|
|
|
| 9 |
|
|
| 21 |
|
|
| Welded |
|
| 2 | Rod |
|
|
| |
|
| 10 |
|
| 99 | 57 |
|
|
|
| |
39. Attach the Press Bracket (94) to the Leg | 39 |
|
|
Press Arm (96) with a 5/16” x 3” Bolt (111) |
|
| |
|
|
| |
and a 5/16” Nylon Locknut (3). |
|
|
|
Wrap the Leg Press Cable (99) around a 3 1/2” |
|
|
|
Pulley (15). Attach the Pulley to the Press |
|
|
|
Bracket (94) with the 3/8” x 2” Bolt (12) and a |
|
|
|
3/8” Nylon Locknut (21). |
|
| 96 |
Slide a 5/16” Flat Washer (8) onto a 5/16” x |
|
| 12 |
|
| 3 | |
2 3/4” Bolt (11). Insert the Bolt through the | 11 |
| |
|
| ||
lowest hole in the Rear Seat Frame (100) |
| 8 | 94 |
|
| ||
from the indicated side. (Note: The three |
| 99 | 111 |
holes are for cable adjustment.) Tighten a |
|
|
|
5/16” Nylon Jam Nut (93) onto the Bolt. Slide |
| 15 | |
the end of the Leg Press Cable (99) onto the |
| ||
end of the Bolt. Thread another 5/16” Nylon |
|
| 21 |
|
|
| |
Jam Nut onto the Bolt. Do not fully tighten |
|
|
|
the second Jam Nut. There must be room |
|
|
|
between the two Jam Nuts for the end of |
|
|
|
the Cable to pivot. |
| 100 |
|
|
|
| 93 |
18
