Manuals / Weider / Fitness & Sports / Home Gym

Weider WESY96400 user manual Weider, Nameplate, Decal

Models: WESY96400

1 34

Download 34 pages 36.08 Kb

Page 21

WEIDER

46.Remove the adhesive backing from the PRO 9640 decal and apply it to the Front Upright (42) under the “WEIDER” nameplate as shown.

46

WEIDER

Nameplate

42

PRO 9640

Decal

47.Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW TO USE THE HOME GYM SYSTEM, beginning on page 22 of this manual.

Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables. See TROUBLE-SHOOTING AND MAINTENANCE on page 25.

21

Image 21

Weider WESY96400 user manual Weider, Nameplate, Decal

Contents

USERS MANUAL QUESTIONS?TABLE OF CONTENTS LIMITED WARRANTYICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT IMPORTANT PRECAUTIONS BEFORE YOU BEGIN using the WEIDER PRO 9640 Home Gym SystemFor your benefit, read this manual carefully before FRAME ASSEMBLY ASSEMBLYUpright and Leg Press Upright should be high side of the brackets on the VKRDo not tighten the Nylon Locknuts yet Nylon Locknuts yetTighten all Nylon Locknuts used in steps FRAME ASSEMBLYBe sure that the holes in the Weight Guides are at the top, as shown FRAME ASSEMBLYTube is sitting in the pin grooves in the top Weight Be sure that the holes in the Weight Guides are at the top, as shown“ARM ASSEMBLY.” FRAME ASSEMBLY ARM ASSEMBLYLocate and open the parts bag labeled tighten the Nylon Locknut. The Leg PressDo not tighten the Nylon Locknut yet ARM ASSEMBLYARM ASSEMBLY CABLE ASSEMBLY CABLE ASSEMBLY that the Cable Trap is inside the Long “U” CABLE ASSEMBLY not completely tighten the Nylon Locknut CABLE ASSEMBLY CABLE ASSEMBLY 37. Locate and open the parts bag labeled “SEAT ASSEMBLY.” CABLE ASSEMBLY SEAT ASSEMBLYBackrest must be oriented as shown SEAT ASSEMBLY“VKR ASSEMBLY.” SEAT44. Locate and open the parts bag labeled WEIDER NameplateDecal HOW TO USE THE HOME GYM SYSTEM ADJUSTING THE LEG PRESS PLATE ATTACHING AND REMOVING THE SEATATTACHING THE LEG LEVER TO THE LOW PULLEY STATION WEIGHT RESISTANCE CHART TROUBLE-SHOOTING AND MAINTENANCE High Cable 58 and Low Cable CABLE DIAGRAMS1-High Pulley TOP VIEW 6 High CableMilitary Press Cable 72 and Leg Press Cable Rear Weight Stack-1 4-Rear Seat FrameMilitary Press Cable 6-Pivot ArmORDERING REPLACEMENT PARTS REMOVE THIS PART IDENTIFICATION CHART FROM THE MANUAL 1 Round Inner Cap 1 Round Cover Cap 1 Square Inner Cap 1/2 x 3/4 Spacer 5/16 x 2 Eyebolt 3/4 Round Inner Cap1 3/4 Square Inner Cap 1 1/2 Square Inner Cap 2 Square Inner Cap 2 Square Outer Cap1/4 Nylon Locknut 5/16 Nylon Locknut 5/16 Nylon Jam Nut REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL PART LIST-Model No. WESY96400 DescriptionDescription EXPLODED DRAWING-Model No. WESY96400 R1296A10 43