Command Ds Dial | Western Telematic MT9234, MT5634 manual

MT5634/MT9234 Modem; AT Command Set

Command: Ds	Dial
Values:	s = dial string (phone number and dial modiﬁers)
Default:	none
Description:	Dial telephone number s, where s may up to 40 characters long
	and include the 0–9, *, #, , B, C, and D characters, and the L, P, T,
	V, W, S, comma (,), semicolon (;), !, @, ^ and $ dial string
	modiﬁers.
	Dial string modiﬁers:
	L	Redial last number. (Must be placed immediately
	P	after ATD.)
	P	Pulse-dial following numbers in command.
	T	Tone-dial following numbers in command (default).
	V	Switch to speakerphone mode and dial the following
	W	number. Use ATH command to hang up.
	W	Wait for a new dial tone before continuing to dial.
	,	(X2, X4, X5, X6, or X7 must be selected.)
	,	Pause during dialing for time set in register S8.
	;	Return to command mode after dialing. (Place at end
	!	of dial string.)
	!	Hook ﬂash. Causes the modem to go on-hook for
	@	one-half second, then off-hook again.
	@	Wait for quiet answer. Causes modem to wait for a
		ringback, then 5 seconds of silence, before
		processing next part of command. If silence is not
	^	detected, the modem returns a NO ANSWER code.
	^	Disable data calling tone transmission.
	$	Detect AT&T call card “bong” tone. The character should
		follow the phone number and precede the user’s call card
		number: ATDT1028806127853500$123456789
Command: DS=y Dial Stored Telephone Number
Values:	y = 0–2 (0–1 for SMI-Parallel {internal})
Default:	none
Description:	Dial a number previously stored in directory number y by the
	&Zy=x command. Example: ATDS=2

Command: En	Echo Command Mode Characters
Values:	n = 0 or 1
Default:	1
Description:	E0	Do not echo keyboard input to the terminal.
	E1	Do echo keyboard input to the terminal.

Command: Fn	Echo Online Data Characters
Values:	n = 1
Default:	1
	F0	Enable online data character echo. (Not supported.)
	F1	Disable online data character echo (included for
		backward compatibility with some software).

3-2

Image 10

Western Telematic MT9234, MT5634 manual Command Ds Dial, Command DS=y Dial Stored Telephone Number

Contents

AT Command Set MT5634/MT9234Page Table of Contents MT5634/MT9234 Modem AT Command Set Introduction MT5634/MT9234 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command En Echo Command Mode Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command Fn Echo Online Data Characters Command M n Monitor Speaker Mode Command H n Hook ControlCommand I n Information Request Command N n Modulation Handshake Command Sr=n Set Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr? Read Register Value Command Zn Modem Reset Command Result Code OptionsCommand Result Code Selection Command Data Carrier Detect DCD Control Command &Fn Load Factory Settings Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Gn V.22bis Guard Tone Control Command &Qn Asynchronous Communications Mode Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command Data Set Ready DSR Control Command &Wn Store Current Conﬁguration Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Zy=x Store Dialing Command Command \B n Transmit Break Command \A nCommand \K n Break Control Command \Tn Inactivity Timer Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Vn Protocol Result Code Command %An Adaptive Answer Result Code Enable Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command View Numbers in Blacklist Command %Hn Direct Connect Enable Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command Cisco Conﬁguration Command $RP n Ring Priority vs. AT Command Priority Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $SB n Serial Port Baud Rate Command #CBAn Callback Attempts Command +VDR=x, y Distinctive Ring ReportCommand #CBDn Callback Delay Command #CBIn Local Callback Inactivity Timer Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBNy=x Command #Sx Enter Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634/MT9234 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634/MT9234 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free