Command P Pulse Dialing | Western Telematic MT9234, MT5634 specification

MT5634/MT9234 Modem; AT Command Set

Command: P	Pulse Dialing
Values:	P, T
Default:	T
Description:	Conﬁgures the modem for pulse (non-touch-tone) dialing. Dialed
	digits are pulsed until a T command or dial modiﬁer is received.

Command: Qn	Result Codes Enable/Disable
Values:	n = 0 or 1
Default:	0
Description:	Q0	Enable result codes.
	Q1	Disable result codes.
	Q2	Returns an OK for backward compatibility with
		some software.

Command: Sr=n	Set Register Value
Values:	r = S-register number; n varies
Default:	None
Description:	Set value of register Sr to value of n, where n is entered in
	decimal format (e.g., S0=1).

Command: Sr?	Read Register Value
Values:	r = S-register number
Default:	None
Description:	Read value of register Sr and display it in 3-digit decimal form
	(e.g., S2? gives the response 043).

Command: T	Tone Dialing
Values:	P, T
Default:	T
Description:	Conﬁgures the modem for DTMF (touch-tone) dialing. Dialed
	digits are tone dialed until a P command or dial modiﬁer
	is received.

Command: Vn	Result Code Format
Values:	n = 0 or 1
Default:	1
Description:	V0	Displays result codes as digits (terse response).
	V1	Displays result codes as words (verbose response).

3-4

Image 12

Western Telematic MT9234 Command P Pulse Dialing, Command Qn Result Codes Enable/Disable, Command Sr=n Set Register Value

Contents

AT Command Set MT5634/MT9234Page Table of Contents MT5634/MT9234 Modem AT Command Set Introduction MT5634/MT9234 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command Ds Dial Command DS=y Dial Stored Telephone NumberCommand En Echo Command Mode Characters Command Fn Echo Online Data Characters Command H n Hook Control Command I n Information RequestCommand M n Monitor Speaker Mode Command N n Modulation Handshake Command P Pulse Dialing Command Qn Result Codes Enable/DisableCommand Sr=n Set Register Value Command Sr? Read Register Value Command Result Code Options Command Result Code SelectionCommand Zn Modem Reset Command Data Carrier Detect DCD Control Command &Dn Data Terminal Ready DTR Control Command &En XON/XOFF Pacing ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone Control Command Leased Line Operation Command Pulse Dial Make-to-Break Ratio SelectionCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR Control Command &Tn Loopback Test V.54 Test Commands Command &V Display Current SettingsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing Command Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Nn Error Correction Mode Selection Command \Qn Flow Control SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result Code Command \Xn XON/XOFF Pass-Through Command Data Calling ToneCommand %An Adaptive Answer Result Code Enable Command View Numbers in Blacklist Command %DCn AT Command Control Command Fallback and Fall Forward ControlCommand %Hn Direct Connect Enable Command Cisco Conﬁguration Command $EB n Asynchronous Word Length Command $MB n Online BPS SpeedCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud Rate Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBF? Callback Failed Attempts Display Command #CBFR Callback Failed Attempts ResetCommand #CBIn Local Callback Inactivity Timer Command #CBNy=x Command #CBSn Callback Enable/Disable Command #Pn Set 11-bit ParityCommand #Sx Enter Setup Password Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634/MT9234 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634/MT9234 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free