Command \Qn Flow Control Selection | Western Telematic MT9234

MT5634/MT9234 Modem; AT Command Set

Command: \Nn	Error Correction Mode Selection
Values:	n = 0–5, or 7
Default:	3
Description:	\N0	Non-error correction mode with data buffering
		(buffer mode; same as &Q6).
	\N1	Direct mode.
	\N2	MNP reliable mode. If the modem cannot make an
		MNP connection, it disconnects.
	\N3	V.42/MNP auto-reliable mode. The modem attempts ﬁrst
		to connect in V.42 error correction mode, then in MNP
		mode, and ﬁnally in non-error correction (buffer) mode
		with continued operation.
	\N4	V.42 reliable mode. If the modem cannot make a V.42
		connection, it disconnects.
	\N5	V.42, MNP, or non-error correction (same as \ N3).
	\N7	V.42, MNP, or non-error correction (same as \ N3).

Command: \Qn	Flow Control Selection
Values:	n = 0, 1, or 3
Default:	3	Disable ﬂow control (same as &K0).
Description:	\Q0	Disable ﬂow control (same as &K0).
	\Q1	XON/XOFF software ﬂow control (same as &K4).
	\Q2	CTS-only ﬂow control. Not supported.
	\Q3	RTS/CTS hardware ﬂow control (same as &K3).

Command: \Tn	Inactivity Timer
Values:	n = 0, 1–255
Default:	0
Description:	Sets the time (in minutes) after the last character is sent or
	received that the modem waits before disconnecting. A value of
	zero disables the timer. Applies only in buffer mode.
	Note: You can also set the inactivity timer by changing the
	value of S30.

Command: \Vn	Protocol Result Code
Values:	n = 0, 1, or 2
Default:	1
Description:	\V0	Disables the appending of the protocol result code to
		the DCE speed.
	\V1	Enables the appending of the protocol result code to
		the DCE speed.
	\V2	Same as \V1.

3-10

Image 18

$Western Telematic MT9234, MT5634 manual Command \Nn Error Correction Mode Selection, Command \Qn Flow Control Selection$

Contents

AT Command Set MT5634/MT9234Page Table of Contents MT5634/MT9234 Modem AT Command Set Introduction MT5634/MT9234 Modem AT Command Set AT Command Summary Description Atmtsmodemcr AT Commands Command En Echo Command Mode Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command Fn Echo Online Data Characters Command M n Monitor Speaker Mode Command H n Hook ControlCommand I n Information Request Command N n Modulation Handshake Command Sr=n Set Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr? Read Register Value Command Zn Modem Reset Command Result Code OptionsCommand Result Code Selection Command Data Carrier Detect DCD Control Command &Fn Load Factory Settings Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Gn V.22bis Guard Tone Control Command &Qn Asynchronous Communications Mode Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command Data Set Ready DSR Control Command &Wn Store Current Conﬁguration Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Zy=x Store Dialing Command Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Tn Inactivity Timer Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Vn Protocol Result Code Command %An Adaptive Answer Result Code Enable Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command View Numbers in Blacklist Command %Hn Direct Connect Enable Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command Cisco Conﬁguration Command $RP n Ring Priority vs. AT Command Priority Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $SB n Serial Port Baud Rate Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBIn Local Callback Inactivity Timer Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBNy=x Command #Sx Enter Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #S=x Store Setup Password Register Unit Range Default Description Registers S37 Decimal Registers MT5634/MT9234 Modem AT Command Set Result Codes Terse Verbose Description Delayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEM Changing the Setup Password Country Code Configuration MT5634/MT9234 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free