Country Code Configuration | Western Telematic MT5634, MT9234

Remote Conﬁguration and Country Code Conﬁguration

6.2. Country Code Configuration

Different countries have different requirements for how modems must function. Therefore, before you use the modem, you must conﬁgure it to match the defaults of the country in which you are using it.

If you are comfortable using AT commands, you can conﬁgure your modem using AT commands. You must enter these commands in your communication program’s terminal window.

To conﬁgure the modem for a speciﬁc country, execute the following AT commands:

1.Type AT%T19,0,nn (nn stands for country code). Press [Enter]. OK is displayed.

2.Then save the changes by issuing the following command:

AT&F&W

3.To verify that the correct country has been conﬁgured, issue the following command:

ATI9

4.The country code is then displayed in decimal format.

The following is an example of country, AT commands, and result codes.

	AT Command
Country	(Hexadecimal)	Result Code (Decimal)

Euro/NAM	AT%T19,0,34 (default)	52
Australia	AT%T19,0,01	1

Czech Republic	AT%T19,0,25	37

Japan	AT%T19,0,10	16

New Zealand	AT%T19,0,9	9

6-3

Image 33

Western Telematic MT5634, MT9234 manual Country Code Configuration

Contents

MT5634/MT9234 AT Command SetPage Table of Contents MT5634/MT9234 Modem AT Command Set Introduction MT5634/MT9234 Modem AT Command Set Description AT Command Summary Atmtsmodemcr AT Commands Command DS=y Dial Stored Telephone Number Command Ds DialCommand En Echo Command Mode Characters Command Fn Echo Online Data Characters Command I n Information Request Command H n Hook ControlCommand M n Monitor Speaker Mode Command N n Modulation Handshake Command Qn Result Codes Enable/Disable Command P Pulse DialingCommand Sr=n Set Register Value Command Sr? Read Register Value Command Result Code Selection Command Result Code OptionsCommand Zn Modem Reset Command Data Carrier Detect DCD Control Command &En XON/XOFF Pacing Control Command &Dn Data Terminal Ready DTR ControlCommand &Fn Load Factory Settings Command &Gn V.22bis Guard Tone Control Command Pulse Dial Make-to-Break Ratio Selection Command Leased Line OperationCommand &Qn Asynchronous Communications Mode Command Data Set Ready DSR Control Command &V Display Current Settings Command &Tn Loopback Test V.54 Test CommandsCommand &Wn Store Current Conﬁguration Command &Zy=x Store Dialing Command Command \A n Command \B n Transmit BreakCommand \K n Break Control Command \Qn Flow Control Selection Command \Nn Error Correction Mode SelectionCommand \Tn Inactivity Timer Command \Vn Protocol Result Code Command Data Calling Tone Command \Xn XON/XOFF Pass-ThroughCommand %An Adaptive Answer Result Code Enable Command View Numbers in Blacklist Command Fallback and Fall Forward Control Command %DCn AT Command ControlCommand %Hn Direct Connect Enable Command Cisco Conﬁguration Command $MB n Online BPS Speed Command $EB n Asynchronous Word LengthCommand $RP n Ring Priority vs. AT Command Priority Command $SB n Serial Port Baud Rate Command +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBFR Callback Failed Attempts Reset Command #CBF? Callback Failed Attempts DisplayCommand #CBIn Local Callback Inactivity Timer Command #CBNy=x Command #Pn Set 11-bit Parity Command #CBSn Callback Enable/DisableCommand #Sx Enter Setup Password Command #S=x Store Setup Password Registers Register Unit Range Default Description S37 Decimal Registers MT5634/MT9234 Modem AT Command Set Terse Verbose Description Result Codes Delayed Example %%%ATMTSMODEM Remote Configuration and Country Code Configuration Changing the Setup Password Country Code Configuration MT5634/MT9234 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free