Command #CBNy=x, Store Callback Password | Western Telematic MT5634

		AT Commands
Command: #CBF? Callback Failed Attempts Display
Values:		N/A
Default:		N/A
Description:		Requests the number of failed callback passwords since reset
		or power-up. This number can be stored to nonvolatile memory
		using the &W command.
Command:	#CBFR Callback Failed Attempts Reset
Values:		N/A
Default:		N/A
Description:		Resets the number of failed callback passwords to 0. This does
		not reset the number stored in nonvolatile memory.
Command:	#CBIn	Local Callback Inactivity Timer
Values:		n = 1–255
Default:		20
Description:		Sets the time (in minutes) that the modem waits for a command
		before forcing the user to enter the setup password again.
Command: #CBNy=x
		Store Callback Password
Values:		y = 0–29
		x = password
Defaults:		None
Description:		Sets the callback security password for the y memory location.
		The password must have 6 to 10 characters, and cannot include
		the + or - ¬characters.
Command:	#CBPn	Callback Parity
Values:		n = 0, 1, or 2
Default:		0
Description:		Sets parity for the callback security messages.
		#CBP0 No parity.
		#CBP1 Odd parity.
		#CBP2 Even parity.
Command:	#CBRy	Callback Security Reset
Values:		y = 0–29
Default:		None
Description:		Clears the password and phone number in the y memory location.

3-15

Image 23

Western Telematic MT5634 Command #CBF? Callback Failed Attempts Display, Command #CBFR Callback Failed Attempts Reset

Contents

MT5634/MT9234 AT Command SetPage Table of Contents MT5634/MT9234 Modem AT Command Set Introduction MT5634/MT9234 Modem AT Command Set Description AT Command Summary Atmtsmodemcr AT Commands Command Fn Echo Online Data Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command En Echo Command Mode Characters Command N n Modulation Handshake Command H n Hook ControlCommand I n Information Request Command M n Monitor Speaker Mode Command Sr? Read Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr=n Set Register Value Command Data Carrier Detect DCD Control Command Result Code OptionsCommand Result Code Selection Command Zn Modem Reset Command &Gn V.22bis Guard Tone Control Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Fn Load Factory Settings Command Data Set Ready DSR Control Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command &Qn Asynchronous Communications Mode Command &Zy=x Store Dialing Command Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Wn Store Current Conﬁguration Command \K n Break Control Command \A nCommand \B n Transmit Break Command \Vn Protocol Result Code Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Tn Inactivity Timer Command View Numbers in Blacklist Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command %An Adaptive Answer Result Code Enable Command Cisco Conﬁguration Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command %Hn Direct Connect Enable Command $SB n Serial Port Baud Rate Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $RP n Ring Priority vs. AT Command Priority Command #CBDn Callback Delay Command +VDR=x, y Distinctive Ring ReportCommand #CBAn Callback Attempts Command #CBNy=x Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBIn Local Callback Inactivity Timer Command #S=x Store Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #Sx Enter Setup Password Registers Register Unit Range Default Description S37 Decimal Registers MT5634/MT9234 Modem AT Command Set Terse Verbose Description Result Codes Delayed Example %%%ATMTSMODEM Remote Configuration and Country Code Configuration Changing the Setup Password Country Code Configuration MT5634/MT9234 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free