hk
Explosion Hazard
Connect dryer to a regulated gas supply.
Use a new flexible gas supply line.
If L.P. gas is used, the L.P. gas supply must not exceed 13” water column.
Failure to do so can result in death, explosion, or fire.
A n This installation must conform with American National Standard, National Fuel Gas Code ANSI
2223.1
B . The design of this dryer has been
B.T.U. rating indicated on the
-
model/serial rating plate. Burner input adjustments are not required when the dryer is operated up to this elevation.
When installed above 10,000 feet, a four percent (4%) reduction of the burner B.T.U. rating shown on the model/serial rating plate is required for each 1,000 foot increase in elevation. For assistance when converting to other gas types and/or installing above 10,000 feet elevation, contact your local service company.
C n Check that the dryer is equipped with the correct burner for the particular type of gas used. Burner information can be found on the model/serial rating plate in the door well of the appliance. If this information does not agree with the type of gas available, see your dealer.
D . This dryer is equipped for use with NATURAL GAS. it is certified by the American Gas Association for
manufactured, mixed and L.P (propane and butane) gases with
appropriate conversion. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. Conversion
Page 4
must be done by a qualified service technician. Gas conversion kit part numbers are listed on the gas valve burner base.
n Provide a rigid gas supply line of
Fn If local codes and ordinances
permit, it is recommended that new, flexible metal tubing,
shutoff valve
G WThe supplv line shall be equipped with ‘a shutoff valve. This valve should be located in the same room as the dryer and should be in a location that allows ease of opening and closing. Do Not block access to the shutoff valve.
H
If rigyd pipe is used as a ga combination
must be used to’dbtain a:
In Make sure that lower edges of the cabinet, plus the back and bottom sides of the dryer are free of obstructions to permit adequate clearance of air openings for combustion air, See “Recessed area and closet installation instructions,” on Page 11, for minimum spacing requirements.
J n For ease of installation, operation and servicing (if ever needed) adequate space should be provided around the dryer.
K n A 1/&inch, NPT plugged tapping, accessible for test gauge connection, must be installed immediately upstream of the gas supply connector to the dryer. The dryer and its individual shutoff
valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of l/2 psig
(3.4 kPa).
The dryer must be isolated from the gas supply piping system by closing the individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than l/2 psig
(3.4 kPa).
Electrical requirements
Electrical Shock Hazard
Plug into a grounded
Do not remove ground prong. Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the ground path is adequate.
Observe all governing codes and ordinances.
A
breaker | is recommended. | It is |
| ||
recommended | that | a separate |
| ||
circuit | serving | only | this | appliance | be |
provided. |
|
|
|
| |
Recommended |
| ground |
| ||
method |
|
|
|
| |
For your personal safety, this dryer must be grounded. This dryer is equipped with a power supply cord having a
grounded in accordance with National Electrical Code ANSVNFPA 70 - latest edition (**, Page 5) and all local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the
