Built-in opening reaujrrements
Lorner |
| I- | |
location | - | ||
2” (5.1 | cm) | ||
minimum |
| ||
door | to cabinet |
| |
or wall. |
|
| |
Cut | openings | - | |
Water | line: |
| |
l/2” | (1.3 cm) |
| |
;;gy;pe.
|
|
|
| / |
|
Unshaded | area | must | be |
| |
free ot pipes, wires, and |
| ||||
drain | hose. | Electrical |
|
| |
outlet | must | be | installed | 4- | 24”- |
in an | adjacent | cabinet, |
| (61 cm) | |
it needed.
’ 11
Electrical Shock Hazard
Electrical wiring, water supply line, and drain line must not contact any exposed terminals of the dishwasher wiring.
Cabinet opening must completely enclose sides, top and back of dishwasher.
Failure to follow these
Grommet | I |
| ||
(Part | No. |
| ||
|
| |||
3027971 | t1n |
| ||
required tar | ‘ ‘;” | ““I’, | ||
electrical |
| |||
cable | hole |
| ||
(6.4 cm) J | ||||
cut in | metal | |||
|
| |||
cabinet. |
|
| ||
| au | ,” | /(12.7cm) | |
|
|
| ||
|
| (a6Ycm) |
e 6” | 6” | min. trom |
underside | ||
(15.2 cm) | (15.2 cm) | Of |
| It- | countertop |
|
| |
|
| zm) |
Llo” |
|
|
(25.4 | cm) |
|
| (12.: cm)\r | ‘t, |
instructions can result in death or electrical shock.
Do Not run water or drain lines or electrical wiring where they can cross in front of or contact dishwasher motor or legs.
Do Not install dishwasher over carpeted flooring.
Do Not kink the power supply cable between the dishwasher and cabinet.
Protect dlshwasher and water lines leadlng to dlshwasher against freezlng. Damage from freezlng Is not covered by the warranty.
Proper electrical, drain and water supply lines must be available or must be installed, as specified, within the shaded area. See
“Electrical requirements,” ‘Water requirements,” and “Drain requirements” sections.
Important: Observe all governing codes and ordinances.
It is recommended that the electrical, drain and water supply lines be located as close to the rear wall as possible.
Check the locatlon where the dishwasher will be installed. The location must provide:
l Easy access to water, electricity and drainage lines.
l Convenient loading - the best location is to the left or right of the kitchen sink.
l Square opening for proper dishwasher operation and appearance.
l Cabinet front that is perpendicular to the floor.
l Protection so that the water inlet valve and drain cannot freeze.
l l/4” (0.64 cm) minimum clearance between the motor and the flooring to prevent the motor from overheating.
For installations where the dishwasher will be left unused and subject to freezing temperatures, see the “Storing Your Dishwasher” or “Moving or winterizing your dishwasher”
section of the dishwasher Use and Care Guide.
Parts su Ifed for insta‘ppation:
l 2 drain hose clamps
l 2
Remove parts from bag. Check that all parts were supplied.
Tools and materials required for hstaIIation:
l electric drill
l Phillips screwdriver
l 2 adjustable wrenches l
lpliers
l pipe wrench
l keyhole saw
l 90” elbow with 318” N.P.T. external threads on one end. The size of the other end must fit your water supply line.
l tubing cutter
l
l wire stripper and utility knife
l 5/16” and l/4” nut driver or hex socket
l 3
l gloves
l safety glasses
Page 3
