INSTALLATION INSTRUCTIONS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Flat-blade screwdriver

 

Tin snips (new vent

 

#2 Phillips screwdriver

 

installations)

 

Level

Adjustable wrench that

 

 

 

Vent clamps

opens to 1" (25 mm) or

 

 

 

hex-head socket wrench

 

Caulking gun and

(for adjusting dryer feet)

 

compound (for installing

Wire stripper (direct wire

 

 

new exhaust vent)

installations)

 

Tape measure

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

4 leveling legs

Parts needed:

Check local codes. Check existing electrical supply and venting and see “Electrical Requirements” and “Venting Requirements” before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For information on ordering, please refer to the “Assistance or Service” section. You may also contact the dealer from whom you purchased your dryer.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

A UL listed strain relief.

LocationRequirements

You will need

A location that allows for proper exhaust installation. See “Venting Requirements.”

A separate 30-amp circuit.

If you are using a power supply cord, a grounded electrical outlet located within 2 ft (610 mm) of either side of the dryer. See “Electrical Requirements.”

A sturdy floor to support the total weight (dryer and load) of

200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.

A level floor with a maximum slope of 1" (25 mm) under entire dryer.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

43½"

(1105 mm)

*29¼"

22¼"

(565 mm)

(743 mm)

29"

 

 

(737 mm)

*Most installations require a minimum 5" (127 mm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Requirements.”

4

Page 4
Image 4
Whirlpool W10151492B, W10151493B manual Installation Instructions, ToolsandParts, LocationRequirements

W10151493B, W10151492B specifications

The Whirlpool W10151492B and W10151493B are high-performance refrigerator water filters designed to enhance the quality of drinking water and ice while maintaining the overall health and safety standards for your household. These models are compatible with a range of Whirlpool refrigerators and provide an efficient solution for reducing contaminants commonly found in tap water.

One of the main features of the W10151492B and W10151493B is their advanced filtration technology. Employing an activated carbon filtration system, these filters are capable of reducing harmful impurities such as chlorine, lead, mercury, pesticides, and pharmaceuticals. This not only improves the taste and odor of the water but also ensures that it is safe for consumption, making these filters an ideal choice for families looking to consume clean, refreshing water directly from their refrigerator.

Another defining characteristic of these filters is their focus on convenience and user-friendliness. Designed for easy installation and replacement, both models come with clear instructions to ensure that users can effortlessly replace the filter themselves. This eliminates the need for professional installation services, making maintenance simpler and more accessible for the average consumer.

The W10151492B and W10151493B filters also boast a high capacity, with the ability to filter up to approximately 200 gallons of water, depending on water quality and usage. This long-lasting capability aids in reducing the frequency of filter replacements, thus minimizing both cost and environmental impact.

In addition to their functional benefits, these filters are certified by the National Sanitation Foundation (NSF), affirming that they meet stringent public health and safety standards. This certification provides peace of mind to consumers, ensuring that their filtration system is not only effective but also trustworthy.

Moreover, the W10151492B and W10151493B demonstrate an eco-conscious approach; they help reduce reliance on bottled water, contributing to less plastic waste in landfills. Choosing these filters represents a smart choice for environmentally aware households.

In summary, the Whirlpool W10151492B and W10151493B filters stand out with their combination of advanced filtration technology, ease of installation, long-lasting capacity, and certification by NSF. These features work together to provide clean, safe, and great-tasting water, catering to the needs of modern households who prioritize health, convenience, and sustainability.