DEALER SERVICE

The information in this section is written for dealer ser- vice personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in this type of repair, you may be time and money ahead to replace complete assemblies.

■Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

GEARBOX REPAIR

NOTE: Read this entire section before starting any repair. Many steps are dependent on each other.

1.Fill gearbox with SAE 80W or 90W gear lube. Proper oil level for wing and center gearboxes is between lowest ring and end of dipstick. On splitter gearbox, fill gearbox until oil runs out the side plug on gearbox.

NOTE: Repair to these gearboxes is limited to replacing bearings, seals, and gaskets. Replacing gears, shafts, and a housing is not cost effective. Purchasing a complete gearbox is more economi- cal.

2.Inspect gearbox for leakage and bad bearings. Leakage is a very serious problem and must be corrected immediately.

NOTE: Bearing failure is indicated by excessive noise and side-to-side or end-play in gear shafts.

Seal Replacement (Figure 10)

Recommended sealant for gearbox repair is Permatex® Aviation 3D Form-A-Gasket or equivalent. Leakage can occur at the vertical or horizontal gaskets and shaft seals.

Leakage at the horizontal gasket or seal can be repaired without removing the gearbox from the cutter.

Seal Installation

NOTE: Proper seal installation is important. An improp- erly installed seal will leak.

1.Clean area in housing where seal outer diameter (OD) seats. Apply a thin coat of Permatex.

2.Inspect area of shaft where seal seats. Remove any burrs or nicks with an emery cloth.

3.Lubricate gear shaft and seal lips.

4.Place seal squarely on housing, spring-loaded lip toward housing. Select a piece of pipe or tubing with an OD that will sit on the outside edge of the seal but will clear the housing. Tubing with an OD that is too small will bow seal cage and ruin seal.

5.Carefully press seal into housing, avoiding distortion to the metal seal cage.

1.Seal

2.Pipe or tube

3.Seal seat

4.Casting

Pipe or tube must press at outer edge of seal.

Incorrect

Installation

Figure 10. Seal Installation

Vertical Shaft Seal Replacement (Figure 11)

1.Disconnect and remove driveline from the gearbox.

2.Remove dipstick breather assembly (30) and siphon gear lube from housing through this opening.

3.Remove crossbar (see page 30).

4.Remove retaining ring (33) and output oil seal (15). Replace output oil seal (15) with new seal. Install retaining ring (33).

NOTE: Distortion to seal cage or damage to seal lip will cause seal to leak.

5.Fill gearbox with SAE 80W or 90W gear lube to the center of the horizontal shaft.

6.Remove and replace any seal damaged in installation.

MAN0764 (11/5/2008)

Dealer Service 25

 

 

Page 24 Page 26
Page 25
Image 25
Woods Equipment BW2400XQ, BW1620XQREV manual Dealer Service, Gearbox Repair, Vertical Shaft Seal Replacement Figure
Page 24 Page 26

BW2400X, BW1620XQREV, BW2400XQ, BW1620X, BW1620XQ specifications

Woods Equipment has established itself as a trusted name in the landscape and agricultural equipment sector, offering a wide range of high-performance products tailored to meet various needs. Among its standout offerings are the BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models, known for their robust design and exceptional functionality.

The BW1620XQ is designed for efficient brush cutting, making it an ideal choice for land maintenance and clearing dense underbrush. One of its main features is the heavy-duty construction, which ensures durability even under the toughest conditions. This model is equipped with a reinforced deck, providing added strength and longevity. It also features a powerful PTO-driven cutting system, allowing it to tackle tough growth with ease.

The BW1620X model offers similar capabilities to the BW1620XQ but is optimized for lighter tasks and smaller properties. It shines in residential applications, where maneuverability and ease of use are paramount. This model is lightweight and easy to attach, making it a favorite among homeowners who require a reliable tool for maintaining their yards and gardens.

For those requiring larger-scale solutions, the BW2400XQ provides increased cutting width and efficiency. This model excels in farm and large property applications, where speed and power are essential. Featuring advanced blade technology, the BW2400XQ offers superior cutting performance and reduced maintenance needs. Additionally, it boasts adjustable height settings, allowing users to customize their cutting experience based on the terrain and type of vegetation.

The BW1620XQREV is a revolutionary model that incorporates newer technology for even better performance and user experience. This model offers enhanced features such as improved blade design for finer cuts and an innovative quick-attach system that enables fast connectivity and disconnection from tractors.

Finally, the BW2400X model is the standard version of the BW2400XQ, providing similar power and efficiency without some of the specialized features, making it a cost-effective solution for users who need reliable equipment without as many bells and whistles.

In conclusion, Woods Equipment's BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models each feature unique characteristics tailored to specific applications, ensuring users can find the right tool for their needs, whether for residential landscaping or large-scale agricultural tasks. Their emphasis on durability, efficiency, and user-friendly design makes them a preferred choice across various sectors.
Top Page Image Contents