Install Wing Driveline

(Figure 33)

3.Clutch shield

4.Wing driveline, complete

Figure 33. Right Driveline Installation

1.Remove knob on top of clutch shield (3) and raise shield.

2.Slide clutch of driveline (4) over wing gearbox shaft and align holes with groove.

3.Secure driveline to shaft using cap screws and lock nuts supplied with driveline.

4.Slide opposite end of driveline over splitter gearbox and secure using cap screws and lock nuts supplied with driveline.

5.Repeat process for left driveline.

FILL GEARBOXES

1.Remove top and side plugs from gearbox.

2.Fill gearbox with SAE 80W or 90W EP oil until it runs out of side level hole. Install plug in the side hole and vented dipstick in the top.

3.Allow oil to drain into the lower bearings and recheck oil level.

4.Fill gearboxes if needed.

HYDRAULIC CYLINDER

Attach hose to each elbow.

OPTIONAL EQUIPMENT

Install Tandem Wheel Assembly - Center

(Figure 34)

1.Slide spring wheel arm assembly (1) over right side of center wheel yoke tube and secure into position using four cap screws (22) and flanged lock nuts (23). Repeat step to install spring wheel arm assembly on left side of center wheel yoke tube.

2.Place tandem wheel bracket (16) around lower lower spring arm (13) and insert flange pin (17). Secure flange pin to tandem wheel bracket using cap screw (18) and flat washer (19).

3.Insert wheel hubs (15) into both sides of tandem wheel bracket (16) and align holes.

4.Secure into position using cap screws (20) and flanged lock nuts (21).

5.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown)

Install Tandem Wheel Assembly - Wing

(Figure 34)

1.Place carriage bolt (67), Figure 32, through holes on wing. Carriage bolts are on the outside; lock nuts on the underside.

2.Attach wing wheel yoke (2), Figure 34, to the wing using pivot pins (31). See Figure 32 for pin and hardware installation. Make sure pin flange is on the underside of the deck.

3.Secure pivot pins to deck using carriage bolts (67) and flange lock nuts (53).

4.Place tandem wheel bracket (16), Figure 34, around lower spring arm (3) and insert flange pin (17). Secure flange pin to tandem wheel bracket using cap screw (18) and flat washer (19).

5.Insert wheel hubs (15) into both sides of tandem wheel bracket (16) and align holes. Secure using cap screws (20) and flanged lock nuts (21).

6.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Set tire pressure to a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

40 Assembly

MAN0764 (11/5/2008)

 

 

Page 39 Page 41
Page 40
Image 40
Woods Equipment BW2400XQ, BW1620XQREV manual Fill Gearboxes, Hydraulic Cylinder, Optional Equipment
Page 39 Page 41

BW2400X, BW1620XQREV, BW2400XQ, BW1620X, BW1620XQ specifications

Woods Equipment has established itself as a trusted name in the landscape and agricultural equipment sector, offering a wide range of high-performance products tailored to meet various needs. Among its standout offerings are the BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models, known for their robust design and exceptional functionality.

The BW1620XQ is designed for efficient brush cutting, making it an ideal choice for land maintenance and clearing dense underbrush. One of its main features is the heavy-duty construction, which ensures durability even under the toughest conditions. This model is equipped with a reinforced deck, providing added strength and longevity. It also features a powerful PTO-driven cutting system, allowing it to tackle tough growth with ease.

The BW1620X model offers similar capabilities to the BW1620XQ but is optimized for lighter tasks and smaller properties. It shines in residential applications, where maneuverability and ease of use are paramount. This model is lightweight and easy to attach, making it a favorite among homeowners who require a reliable tool for maintaining their yards and gardens.

For those requiring larger-scale solutions, the BW2400XQ provides increased cutting width and efficiency. This model excels in farm and large property applications, where speed and power are essential. Featuring advanced blade technology, the BW2400XQ offers superior cutting performance and reduced maintenance needs. Additionally, it boasts adjustable height settings, allowing users to customize their cutting experience based on the terrain and type of vegetation.

The BW1620XQREV is a revolutionary model that incorporates newer technology for even better performance and user experience. This model offers enhanced features such as improved blade design for finer cuts and an innovative quick-attach system that enables fast connectivity and disconnection from tractors.

Finally, the BW2400X model is the standard version of the BW2400XQ, providing similar power and efficiency without some of the specialized features, making it a cost-effective solution for users who need reliable equipment without as many bells and whistles.

In conclusion, Woods Equipment's BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models each feature unique characteristics tailored to specific applications, ensuring users can find the right tool for their needs, whether for residential landscaping or large-scale agricultural tasks. Their emphasis on durability, efficiency, and user-friendly design makes them a preferred choice across various sectors.
Top Page Image Contents