Machine Specifications | Woodstock M1054 specification

Model M1054 (Mfg. Since 4/10)

MACHINE

SPECIFICATIONS

© Woodstock International, Inc. • Phone #: (360) 734-3482 • Web: www.shopfox.biz

MOdEl M1054

10" x 18" METAl CuTTINg bANdSAw

Product Dimensions:
Weight	705 lbs.
Length/Width/Height	673⁄4 x 241⁄2 x 411⁄2 in.
Foot Print (Length/Width)	47 x 21 in.
Shipping Dimensions:
Type	Wood Slat Crate
Weight	770 lbs.
Length/Width/Height	69 x 27 x 46 in.
Electrical:
Required Power Source	220V-240V, Single-Phase, 60Hz
Minimum Circuit Size	20 Amp
Switch	Push Button ON/OFF
Switch Voltage	220V
Cord Length	7 ft.
Cord Gauge	14 Gauge
Plug Included	No
Recommended Plug Type	NEMA L6-20 or 6-20
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	11⁄2 HP
Voltage	220V
Phase	Single-Phase
Amps	15.5A
Speed	1725 RPM
Cycle	60 Hz
Power Transfer	Pulley + Gear
Bearings	Shielded & Lubricated
Main Specifications:
Operation Information
Blade Speeds	114, 196, 288, 377 FPM
Blade Length	1211⁄2 in.
Table Information
Table Length	30 in.
Table Width	61⁄2 in.
Floor-To-Vise Height	223⁄4 in.

-2-

Image 2

Woodstock M1054 owner manual Machine Specifications

Contents

Model M1054 10 x 18 Metal Cutting Bandsaw Manual Insert Copyright October, 2010 by Woodstock INTERNATIONAL, INC Machine Specifications Cutting Capacities Parts Breakdown Model M1054 Mfg. Since 4/10 Parts List Description SAW BOW XPN03M Bandsaw Page Contents Maintenance Woodstock Technical Support SpecificationsIntroduction Controls and Features Control Panel M1048 control panel Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Extension Cords Electrical220V Operation Grounding Inventory SetupUnpacking Box Inventory Figure Qty Machine Placement Cleaning Machine Mounting to Shop Floor Bolting to Concrete Floors Shipping Bracket To setup the workstop do these stepsMoving & Placing Unit Workstop Factory adjustments that should be verified Recommended AdjustmentsTo adjust the feed stop bolt, do these steps Chip Tray Test Run To test run the bandsaw, do these steps Vise OperationsGeneral To rapidly change the vise jaw gap, do these steps To adjust the positive stops, do these steps Squaring vise to blade Rear Vise Jaw Stop To adjust the rear blade guide arm Blade Guide Arms Blade Selection To select the correct blade TPI do these steps To change blade speeds, do these steps Blade SpeedFeed Rate To set the feed rate, do these steps Coolant System Coolant system reservoir Cover Coolant Control Valve Cutting Fluid Biological and Poison Tips for horizontal cutting Bandsaw AccessoriesOperation Tips Lubrication MaintenanceCleaning Make Sure that your machine To change the gear oil, do these steps Gear box Service Troubleshooting Bandsaw Operations Blade Change To change the blade on the bandsaw, do these steps To adjust the blade tracking on the bandsaw, do these steps Blade Tension & Tracking Blade Guide Bearings To adjust the blade guide bearings, do these stepsTo adjust the blade guide roller bearings, do these steps Squaring Blade to Table To square the blade the to the table, do these steps Limit switch SQ1 Electrical Components Model M1048 220V Wiring Diagram OFF Guides Blade Guides Parts List PART# Description Drive Wheel Parts Breakdown Drive Wheel Parts List Breakdown Main Parts List XPSB30M CAPSCREWM6-1X45 Label Placement Warranty Warranty Registration Comments BOX BELLINGHAM, WA