Woodstock W1814 manual Af`ek`e, Kf\\af`ekfek\af`ek\i#fk\j\jk\gj1

N(/(+Fne\ijDXelXcD]^%('&'/"

<[^\Af`ek`e^

The purpose of edge jointing is to produce a finished, flat-edged surface (see =`^li\j*-&*.) that is suitable for joinery or finishing. It is also a necessary step when squaring rough or warped stock.

EFK@:<

@] pfl Xi\ efk \og\i`\eZ\[ n`k_ X af`ek\i# j\k k_\ [\gk_ f] Zlk kf '# Xe[ giXZk`Z\ ]\\[`e^ k_\ nfibg`\Z\ XZifjj k_\ kXYc\j Xj [\jZi`Y\[ Y\cfn% K_`j gifZ\[li\ n`cc Y\kk\i gi\gXi\ pfl ]fi k_\ XZklXcfg\iXk`fe%

FG<I8K@FEJ

Kf\[^\af`ekfek_\af`ek\i#[fk_\j\jk\gj1

(% Read and understandJ8=<KP, beginning on GX^\,.

)% Make sure your stock has been inspected for danger- ous conditions as described in the JkfZb@ejg\Zk`fe I\hl`i\d\ekj instructions, beginning on GX^\)(.

*% Set the cutting depth for your operation. Efk\1 N\ jl^^\jkY\kn\\e(Ð(-Xe[(Ð/]fi\[^\af`ek`e^# lj`e^Xdfi\j_Xccfn[\gk_]fi_Xi[nff[jg\Z`\jfi ]fin`[\jkfZb.

+% Make sure the fence is set to 90˚.

,% If your workpiece is cupped (warped), place it so the concave side is face down (=`^li\*.) on the surface of the infeed table.

-%Start the jointer.

.% Press the workpiece against the table and fence with firm pressure. Use your trailing hand to guide the workpiece through the cut, and feed the workpiece over the cutterhead (see =`^li\*-).

Efk\: @]pflic\X[`e^_Xe[^\kjn`k_`e+f]k_\ Zlkk\i_\X[#c`]k`klgXe[fm\ik_\Zlkk\i_\X[#Xe[ gcXZ\`kfek_\gfik`fef]k_\nfibg`\Z\k_Xk`jfm\i k_\flk]\\[kXYc\%Efn#]fZljpfligi\jjli\fek_\ flk]\\[\e[f]k_\nfibg`\Z\n_`c\]\\[`e^#Xe[ i\g\Xkk_\jXd\XZk`fen`k_pflikiX`c`e^_Xe[`]`k ^\kjn`k_`e+f]k_\Zlkk\i_\X[%Kfb\\gpfli_Xe[j jX]\#;FEFKc\kk_\d^\kZcfj\ik_Xe+]ifdk_\ Zlkk\i_\X[n_\e`k`jdfm`e^

/% RepeatJk\g. until the entire edge is flat.

-24-

=`^li\*-%Typical edge jointing operation.

Portion

Removed with

Jointer

=`^li\*.%Illustration of edge jointing

results.