Woodstock W1814 manual m\clkk`e, KfY\m\cZlkfek\af`ek\i#fk\j\jk\gj1

N(/(+Fne\ijDXelXcD]^%('&'/"

9\m\c:lkk`e^

The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see =`^li\j*/&*0).

The Model W1814 has preset fence stops at 45˚ inward, 90˚, and 45˚ outward (135˚). If your situation requires a different angle, the preset fence stops can be easily adjusted for your needs.

KfY\m\cZlkfek_\af`ek\i#[fk_\j\jk\gj1

(% Read and understand J8=<KP, beginning on GX^\,.

)% Make sure your stock has been inspected for danger- ous conditions as described in the JkfZb@ejg\Zk`fe I\hl`i\d\ekj instructions, beginning on GX^\)(.

*% Set the cutting depth for your operation.

Efk\1 N\jl^^\jkY\kn\\e(Ð(-Xe[(Ð/]fiY\m\c Zlkk`e^#lj`e^Xdfi\j_Xccfn[\gk_]fi_Xi[nff[ jg\Z`\jfi]fin`[\jkfZb%

+% Make sure your fence is set to the angle of your desired cut.

,% If your workpiece is cupped (warped), place it so the concave side is face down on the surface of the infeed table.

-%Start the jointer.

.% With a push block in your leading hand, press the workpiece against the table and fence with firm pressure, and feed the workpiece over the cutterhead.

Efk\: @]pflic\X[`e^_Xe[^\kjn`k_`e+f]k_\ Zlkk\i_\X[#c`]k`klgXe[fm\ik_\Zlkk\i_\X[# Xe[gcXZ\k_\glj_YcfZbfek_\gfik`fef]k_\ nfibg`\Z\k_Xk`jfek_\flk]\\[kXYc\%Efn#]fZlj pfligi\jjli\fek_\flk]\\[\e[f]k_\nfibg`\Z\ n_`c\]\\[`e^#Xe[i\g\Xkk_\jXd\XZk`fen`k_ pflikiX`c`e^_Xe[n_\e`k^\kjn`k_`e+f]k_\ Zlkk\i_\X[%Kfb\\gpfli_Xe[jjX]\#;FEFKc\k k_\d^\kZcfj\ik_Xe+]ifdk_\Zlkk\i_\X[n_\e`k `jdfm`e^

/% Repeat Jk\g. until the angled cut is satisfactory to your needs.

EFK@:<

@] pfl Xi\ efk \og\i`\eZ\[ n`k_ X af`ek\i#j\kk_\[\gk_f]Zlkkf'#Xe[ giXZk`Z\ ]\\[`e^ k_\ nfibg`\Z\ XZifjj k_\ kXYc\j Xj [\jZi`Y\[ Y\cfn% K_`j gifZ\[li\ n`cc Y\kk\i gi\gXi\ pfl ]fi k_\XZklXcfg\iXk`fe%

=`^li\*/% Typical bevel cutting operation.

Portion

Removed With

Jointer

=`^li\*0% Illustration of bevel cutting

results.

FG<I8K@FEJ

-25-