|
|
|
|
|
|
|
|
| Menu structure |
|
|
|
|
|
|
|
|
|
|
■ 3 <INITIAL> |
| ||||||||
|
|
|
|
|
|
|
| Menu item | Choice |
COLOR SYSTEM |
|
|
|
| |||||
Selects the color system when the video signal is input among NTSC, NTSC4.43, PAL, | PAL60/SECAM | ||||||||
PAL60, SECAM. AUTO should normally be selected so that the appropriate color system can be |
| ||||||||
automatically selected depending on the input signal. |
| ||||||||
INPUT A SIGNAL |
|
|
|
| COMPONENT/RGB PC/RGB TV | ||||
| |||||||||
Selects the type of input signal sent to the INPUT A jacks. |
| ||||||||
INPUT B SIGNAL |
|
|
|
| COMPONENT/RGB PC/RGB TV | ||||
| |||||||||
Selects the type of input signal sent to the INPUT B jacks. |
| ||||||||
LANGUAGE |
|
|
|
| /ENGLISH/DEUTSCH/ESPAÑOL/ | ||||
| |||||||||
Selects the language used on the menu. | FRANÇAIS/ITALIANO/ | ||||||||
POWER SAVING | OFF/ON | ||||||||
When no signal is received at the input jacks for longer than 15 minutes, this unit automatically turns off |
| ||||||||
the lamp and enters the standby mode if ON is selected. |
| ||||||||
LAMP RUNNING TIME |
|
| — | ||||||
| |||||||||
Displays the total lamp running time. The lamp running time can be reset on the submenu. |
| ||||||||
RESET |
|
| ALL SETTINGS/ALL MEMORIES/ | ||||||
| |||||||||
Resets all parameters on the menu or parameters in the memory to the factory settings. | CURRENT MEMORY | ||||||||
■ 4 <SETUP>
|
| Menu item | Choice/adjustment range |
INSTALLATION |
|
| FRONT/TABLE, FRONT/CEILING, |
| |||
There are four methods to install this unit; tabletop or | REAR/TABLE, REAR/CEILING | ||
be inverted or rotated according to the setting for the installation method. |
| ||
SCREEN ASPECT | 4:3/16:9* | ||
Selects 4:3 or 16:9 depending on the screen to be used. If 16:9 is selected, vertical adjustment of the image |
| ||
can be made by changing the value of the item “DIGITAL LENS SHIFT”. And automatically makes an |
| ||
adjustment to project the 4:3 input signal without losing any part of it off screen. |
| ||
* DIGITAL LENS SHIFT | |||
The image on the screen can be vertically adjusted within a certain range by digital processing. h moves the |
| ||
image upward and g downward. This adjustment is available only when the screen aspect ratio is set to 16:9. |
| ||
KEYSTONE | |||
If this unit projects on a the screen with some elevation or depression angle at its installation, the image on |
| ||
the screen is distorted into a trapezoid. This parameter electrically corrects the distortion. Increase the value |
| ||
when the upper part of the image is wider. Decrease the value when the lower part if the image is wider. |
| ||
KEYSTONE MODE | NORMAL/FULL | ||
There are two modes; “FULL” that corrects the key stone effect without changing the vertical length of the |
| ||
image, and “NORMAL” that makes vertical correction by shifting the bottom at the same time. Select the |
| ||
appropriate mode to make correction depending on your installation. |
| ||
1Normal correction | 2Full correction |
This correction shifts the bottom of the projected image to correct | This correction adjusts the horizontal distortion without changing |
the horizontal distortion. | the vertical length of the projected image. |
When the upper part of the image is wider than the | When the upper part of the image is wider than the |
lower part, increase the value to the positive (+) | lower part, increase the value to the positive (+) |
direction. | direction. |
When the lower part of the image is wider than the | When the lower part of the image is wider than the | ||
upper part, decrease the value to the negative | upper part, decrease the value to the negative | ||
direction. | direction. | ||
R/C SENSOR |
|
| FRONT&REAR/FRONT/REAR |
| |||
Sets the remote control sensor to be used. This unit has its remote control sensor in two locations: at the front and the rear.
MENU
English