Yamaha DVD-S1500 Audio Menu, TV System NTSC/PAL conversion, Digital output, Analog output

On-screen menu

4:3 panscan

4:3 letterbox

Widescreen

TV System (NTSC/PAL conversion)

Allows you to select [PAL], [NTSC] or [Auto] mode to match your TV system. You can play PAL discs on NTSC monitor, and NTSC discs on PAL monitor. The initial setting is Auto.

Choices: PAL, NTSC, Auto

The following conversions are supported.

Disc		Output format
		Selected mode
Format
	NTSC		PAL	AUTO
NTSC	NTSC		PAL	NTSC
PAL	NTSC		PAL	PAL

Notes:

–In progressive scan mode, the output signals from the VIDEO and S VIDEO jacks are same as the format of the disc you play.

–Some image distortion occurs when switching the NTSC and PAL mode.

–If your TV does not accept the selected mode while you change the [TV System] setting, the screen will be distorted so that you cannot recognize the On-screen menu. When it occurs, you can change the [TV System] settings by the remote control operations. Follow the procedures below.

•Choosing [PAL]:

Press PLAY (u)/2/5/6/PLAY (u) on the remote control.

•Choosing [NTSC]:

Press PLAY (u)/2/5/7/PLAY (u) on the remote control.

Audio Menu

Digital output

Enables you to specify the type of digital output to suit your AV receiver. Select [PCM only] if your receiver is not capable of decoding multi-channel audio.

Select [All] if you connected this unit’s digital out jacks to a multi-channel decoder receiver.

Choices: Off, PCM only, All

Initial setting: All

Note:

– Digital output is not available for SA-CDs.

Analog output

Enables you to specify the type of analog output suitable for your AV receiver.

Choices: Stereo, DolbysurrCompat, 3D sound, Multi-channel

Initial setting: Multi-channel

Stereo: In this setting, the multi-channel audio is down- mixed to a stereo signal. Select this setting when connecting to a TV, stereo amplifier/ receiver, etc.

DolbysurrCompat: Select this setting when using equipment with a Dolby Surround Pro Logic decoder. In this setting, the multi-channel audio (Dolby Digital, MPEG-2, DTS) is downmixed to a Dolby Surround- compatible 2-ch output.

3D sound: In a setup without rear speakers (analogue stereo output), 3D Sound remixes the six channels of digital surround into a two speaker output while retaining all of the original audio information. The result is the sensation of being surrounded by multiple speakers.

Multi-channel: Select this setting when using a multi- channel AV receiver with 6-ch discrete inputs. The multi- channel audio signals those of like DVD-Audio, DVD- Video, and SA-CD are output from the respective 6-ch discrete output jacks. In this mode, this unit will perform DTS decoding, Dolby Digital 5.1-channel decoding, or MPEG Multichannel decoding when applicable, and Dolby Pro Logic II decoding on 2-ch sound tracks except for SA-CD.

PCM output

Enables you to select PCM digital output at 48 kHz or 96 kHz. If you select [48 kHz], PCM data will be converted to 2-ch 48 kHz or less. Select [48 kHz] if the connected equipment cannot process signals with a sampling frequency of 96 kHz or 88.2 kHz.

Choices: 96 kHz, 48 kHz

Initial setting: 96 kHz

Note:

–Signals are converted to either 48 kHz or 44.1 kHz despite the above settings if the disc has copy protection.

–If you select [96 kHz], signals with a sampling frequency of over 96 kHz are converted to 2-ch 88.2 kHz or

96 kHz.

English

13