CONTROLS AND FUNCTIONS
Front panel
1 | 2 | 3 4 5 | 6 | 7 8 9 0 A B C D |
ZONE 2 ON/OFF | FM/AM | l TUNING/CH h |
| |
| XM/ANT |
| PURE DIRECT | MD/TAPE MONITOR |
|
|
|
| |
ZONE CONTROL | EDIT | MEMORY | TUN MODE/DISP |
|
| SEARCH MODE | MAN'L/AUTO FM | AUTO/MAN'L |
|
INTRODUCTION
MASTER |
|
|
|
|
|
A/B/C/D/E |
|
| 1 | 2 | 3 |
CATEGORY |
|
|
|
|
|
ON OFF |
|
|
|
|
|
INPUT |
|
|
| BASS |
|
MAIN ZONE | SPEAKERS |
| 0 |
| |
PHONES | 1 | 1 |
| ||
| A | B | 2 |
| 2 |
ON/OFF |
|
| 3 |
| 3 |
|
|
| 4 |
| 4 |
|
|
| – 5 | 5 | + |
E F G H I
1MASTER ON/OFF
Press inward to the ON position to turn on the power of this unit. Press again to release it outward to the OFF position to turn off this unit.
See page 14 for details.
Note
Even when this unit is turned off, this unit consumes a small amount of power to preserve the memory.
Memory
The memory
2MAIN ZONE ON/OFF
Turns on Main Zone of this unit or sets it to the standby mode.
See page 14 for details.
Notes
•This switch is operational only when MASTER ON/OFF is pressed inward to the ON position.
•In the standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control.
|
|
|
|
|
|
|
|
| 16 |
| 4 | 5 |
| 6 |
| 7 | 8 | 20 | 12 |
|
|
| VOLUME |
| |||||
|
|
|
|
|
|
|
| 26 | 8 |
TREBLE |
| BALANCE |
| DISPLAY LOUDNESS |
|
| |||
1 | 1 |
| 1 | 1 |
| 1 |
| 40 | 4 |
| 0 |
|
| 0 |
| FLAT |
|
|
|
|
|
|
|
|
|
|
|
| |
2 |
| 2 | 2 |
| 2 | 2 | 10 |
|
|
3 |
| 3 | 3 |
| 3 | 3 | 9 | 60 | 2 |
4 |
| 4 | 4 |
| 4 | 4 | 8 | ∞ |
|
– 5 | 5 | + | L 5 | 5 R |
| 5 | 7 | 0 | |
|
|
|
|
|
| 6 |
|
|
|
| (U.S.A. model) |
J | K | L M |
3ZONE 2 ON/OFF
Turns on Zone 2 or set it to the standby mode. When Zone 2 is turned on, signals are output at the ZONE 2 OUT jacks.
Note
This switch is operational only when MASTER ON/OFF is pressed inward to the ON position.
4ZONE CONTROL
Press to control the input source of Zone 2.
Notes
•This button is operational only when Zone 2 is turned on.
•When you press this button, the ZONE 2 indicator flashes in the front panel display for approximately 5 seconds. Select the input source of Zone 2 while the indicator is flashing.
•You can select the preset station or channel when TUNER or XM is selected as the input source of Zone 2.
5Remote control sensor
Receives infrared signals from the remote control.
Note
Switch the remote control ID between ID1 and ID2 when using multiple YAMAHA receivers or amplifiers (see pages 35, 36).
6Front panel display
Shows information about the operational status of this unit.
3