CONTROLS AND FUNCTIONS
7EDIT, SEARCH MODE
Exchanges the assignment of two preset stations with each other when TUNER is selected as the input source (see page 25).
Switches between search modes when XM is selected as the input source (see page 29).
8FM/AM, XM ANT (ANTENNA)
Switches the reception band between AM and FM when TUNER is selected as the input source (see page 20). Shows the reception level of the XM
9TUNING/CH l / h
Selects the tuning frequency when TUNER is selected as the input source (see page 20).
Searches for a radio channel or selects the preset channel number when XM is selected as the input source (see page 27).
0TUN (TUNING) MODE/DISP (DISPLAY)
Switches the tuning mode between automatic (the AUTO indicator turns on as a result) and manual (the AUTO indicator turns off as a result) when TUNER is selected as the input source.
Switches the XM Satellite Radio information shown in the front panel display between channel number/name, category and artist name/song title when XM is selected as the input source (see page 30).
AMEMORY
Stores a station in the system memory (see page 24). Sets this unit to the automatic preset tuning mode (see page 22).
Stores a radio channel in the system memory when XM is selected as the input source (see page 33).
BPURE DIRECT and indicator
Allows you to listen to a source in the purest possible sound. The indicator above it lights up when this function is turned on (see page 16).
CMD/TAPE MONITOR
Allows you to listen to the sound played back on the component connected to the MD/TAPE jacks on the rear panel of this unit.
When the tape deck is used for recording, you can also monitor the sound being recorded.
The MD/TAPE MON indicator in the front panel display lights up when this function is turned on.
Notes
•When this function is on (the indicator lights up), MD/TAPE cannot be selected with the INPUT selector.
•To listen to the source selected with the INPUT selector, press again to turn off the function (the indicator turns off as a result).
•When MD/TAPE is selected with the INPUT selector, this function will not turn on even if MD/TAPE MONITOR is pressed.
DVOLUME
Increases or decreases the sound output level.
Note
This does not affect the OUT (REC) level.
EINPUT selector
Selects the input source you want to listen to or watch.
FA/B/C/D/E, CATEGORY
Selects the preset station group (A to E) when TUNER is selected as the input source (see page 23).
Switches between channel categories or selects the preset channel group when XM is selected as the input source (see page 31).
GPHONES jack
Outputs audio for private listening with your headphones.
Note
Press SPEAKERS A/B so that the SP A/B indicators turn off before you connect your headphones to the PHONES jack.
HSPEAKERS A/B
Turns on or off the speaker set connected to the SPEAKERS A and/or SPEAKERS B terminals on the rear panel each time the corresponding button is pressed (see page 15).
IBASS
Increases or decreases the low frequency response. The 0 position produces a flat response (see page 16).
JTREBLE
Increases or decreases the high frequency response. The 0 position produces a flat response (see page 16).
KBALANCE
Adjusts the sound output balance of the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions (see page 16).
LLOUDNESS
Retains a full tonal range at any volume level to compensate for the human ears’ loss of sensitivity to high and
MPreset station/channel number buttons
(1 to 8)
Selects the preset station number (1 to 8) directly when TUNER or XM is selected as the input source (see page 25).
Note
The XM Satellite Radio features (XM ANT, CH, SEARCH MODE, DISP, CATEGORY, MEMORY and the preset channel number buttons) are only applicable to the U.S.A. model and are operational only when XM is selected as the input source. For details, see “XM SATELLITE RADIO TUNING” on page 26.
4
