Yamaha RX-V1 VOLUME +, ■About the Test Tone

SET MENU Items

2. LOW FREQ. TEST

Use this feature to adjust the Subwoofer volume so it matches the volume of the other speakers in your configuration. Change the setting using the remote control while sitting in the main listening position.

1Press + or –to set the TEST TONE to “ON”, and adjust the volume using VOLUME + so you can hear the tone.

2 Press	%	repeatedly to go to OUTPUT and press + or –to select the speaker you want to compare with the Subwoofer.
	%

•If “SUBWOOFER” is selected, test tones above 90 Hz will not be output from the Subwoofer. The test tone will not necessarily be output from the selected speakers. The output mode of the test tone depends on the settings of the 1. SPEAKER SET items in the SET MENU.

3 Press	%	repeatedly to go to FREQ. and press + or –to select the frequency you want to use.
	%

4Adjust the Subwoofer volume using the controls on the Subwoofer so it matches the volume of the speaker you are comparing it to.

Notes:

•Do not turn up the VOLUME too high.

•If no test tone is heard, turn off the power and make sure all the necessary hookups are correct.

Advanced Operation

Digital Generator

(Wide Band Noise Produced)

NOISE

FREQ.

Band Pass Filter

Center freq.

35 Hz~250 Hz

■About the Test Tone

The test tone is produced by the tone generator.

The tone generator produces a narrow band noise centered at a specified frequency by the band pass filter.

You can change the center frequency from 35 Hz through 250 Hz in one-sixth octave steps.

You can use the test tone not only for adjusting the subwoofer level, but also for checking the low frequency characteristics of your listening room. Low frequency sounds are especially affected by the listener’s position, speaker placement, subwoofer polarity and other conditions.

46

Contents

Page Page 19For US customers only: FCC INFORMATION (for US customers only) Page Contents Introduction Preparations Basic Operation Advanced Operation Introduction Features Getting Started Controls and Functions Introduction Dolby Digital and Dolby Digital Surround EX DTS and DTS ES Comparing Surround Technologies Dolby Surround Digital Sound Fields (DSP) CINEMA-DSP:Dolby Digital + DSP and DTS + DSP Virtual CINEMA DSP and HP CINEMA DSP Multi-functionremote control Various Input and Output Jacks ■About Changing Batteries ■ About handling the remote control ~STANDBY/ON ŸRemote Control Sensor !Front Panel Display ⁄INPUT MODE @INPUT SELECTOR ﬁEFFECT ^6CH INPUT ﬂBALANCE &A/B/C/D/E ‡BASS EXTENSION ON/OFF Power Buttons Display Window Source Select Input Section Operation Section ~Infrared window ŸCLEAR ﬂ+/– &MUTE !RE-NAME ~DTS indicator ŸVIRTUAL indicator !Multi-informationdisplay ⁄STEREO indicator @Input source indicator ~RF (AC-3)input jack ŸAudio equipment jacks !Video equipment jacks ⁄Antenna input terminals @Speaker terminals Preparations Speaker System Configurations Speaker Placement Hookups On-ScreenDisplays (OSD) ■Eight or Seven Speaker Configuration –FullCinema DSP– ■Six Speaker Configuration –HiFi DSP– ■Five Speaker Configuration –Standard5.1 Channel– ■Four Speaker Configuration –MinimumRequirement– ■Placing the Main Speakers ■Placing the Center Speaker ■Placing the Front Effect, Rear and Rear Center Speakers ■When You Use a Projection Screen ■Placing the Subwoofers ■About the Dust Protection Cap ■Connecting a Turntable ■ Connecting a CD Player ■Connecting a Tape Deck TAPE 4 (REC) L and R jacks ■Connecting an MD or DAT Deck (REC) OPTICAL MD (PLAY) ■Connecting an LD Player LD VIDEO ■Connecting a TV or Digital TV D-TVVIDEO jack ■Connecting a Satellite Tuner or Cable TV Tuner (Set Top Box) ■Connecting a VCR VCR 1 IN VCR 1 OUT VCR 1 VIDEO IN jack VCR 1 VIDEO OUT jack ■Using Speaker Cords ■Connecting the Main Speakers MAIN + ■Connecting the Center Speaker CENTER + ■Connecting the Front Effect Speakers FRONT + ■Connecting the Rear and Rear Center Speakers REAR + REAR CENTER + ■Connecting a Rear Subwoofer WARNING ■Impedance Selector switch Front Effect: Rear: ~MAIN jacks ŸCENTER jacks !REAR CT jack ⁄SUBWOOFER jacks @FRONT 6CH INPUT ■Connecting the AC Power Cord ■AC OUTLETS ■ Connecting the indoor FM antenna ■Optional outdoor FM antenna ■Optional outdoor AM antenna ■Connecting the AM loop antenna AM ANT ON SCREEN Summary of SPEAKER SET items 1A through 1G BASS TREBLE BALANCE BASS EXTENSION Page Page Basic Operation Basic Playback AM/FM Tuner Basic Recording SYSTEM POWER STANDBY Select this To reproduce the signal source: from this equipment ■BGV (Back Ground Video) Function Page 1Set 10KEY/DSP to DSP PROGRAM ■Virtual CINEMA DSP and HP CINEMA DSP ■ Normal Stereo Reproduction AM/FM TUNING MODE (AUTO/MAN’L MONO) ■Manually presetting stations Press MEMORY (MAN’L/AUTO FM) 5Press MEMORY (MAN’L/AUTO FM) ■Automatically presetting stations MEMORY 3 Press PRESET/TUNING%or Press PRESET/TUNING (EDIT) again REC OUT/ ZONE ■Special considerations when recording DTS software Advanced Operation SET MENU Items Remote Control Features Adjusting the Levels of the Effect Speakers Setting the Sleep Timer Page ■General procedure for adjusting items 1Set PARAMETER/SET MENU to SET MENU ■1A. CENTER SP (Center Speaker Mode) ■1B. MAIN SP (Main Speaker Mode) ■1C. REAR L/R SP (Rear Speaker Mode) ■1D. REAR CT SP (Rear Center Speaker Mode) ■1E. LFE/BASS OUT (Bass Out Mode) ■1F. FRNT EFCT SP (Front Effect Speaker Mode) ■1G. MAIN LEVEL VOLUME + ■About the Test Tone ■3A. LFE LEVEL ■3B. D-RANGE(Dynamic Range) ■4A. LFE LEVEL Page Page 6.1/ES Page Page <Main Unit Control Area <Component Control Area ■SOURCE SELECT SELECT V-AUX CBSAT TUNER ■Operating a Tuner (TUNER Area) ■ Operating a Tape Deck (TAPE Area) ■Operating a CD Player (CD Area) ■Operating an MD Recorder (MD Area) ■Operating an LD Player (LD Area) ■ Operating a DVD Player (DVD Area) ■Operating a VCR (VCR 1 / VCR 2 / VCR 3 Area) ■Operating a TV or Digital TV (D-TVArea) ■Operating a Cable or Satellite TV Tuner (CBSAT Area) ■Free Area (OPTN and PHONO Areas) POWER Page Page ■Operating the Macro Feature 1Set MACRO ON/OFF to ON ■Programming a Macro Page Page 1Set PARAMETER/SET MENU to PARAMETER LEVEL ■To set the Sleep Timer ■To cancel the Sleep Timer ■A sample of system configuration and connections ■Special considerations when using DTS software For DTS encoded LDs or DVDs For DTS encoded compact discs SOURCE SELECT ZONE2 Additional Information Digital Sound Field Processing (DSP) Hi-Fi DSP-SoundField Program CINEMA-DSP CINEMA-DSPSound Field Program Page ■ Europe Hall A ■ Europe Hall B ■ Europe Hall C ■ U.S.A. Hall D ■ Europe Hall E Page ■Dolby Pro Logic + DSP Sound Field Effect ■Dolby Digital/DTS + DSP Sound Field Effect ■Dolby Digital Matrix 6.1/DTS ES + DSP Sound Field Effect Table of Program Names for Each Input Format ■Program Groups 7~9 ■Program Groups 10~12 ■ Pop/Rock ■ Classical/Opera ■ Pavilion ■ Mono Movie ■ Variety/Sports PARAMETER/SET MENU ■ To reset some of the parameters to the ■ To reset all of the parameters back to the factory preset values Page Page Page Page Appendix Troubleshooting Reference Chart for the INPUT and OUTPUT Jacks CINEMA - EQ Frequency Characteristics Specifications General Page Tuner Remote Control Page Audio Section Video Section FM Section AM Section General Page ■Remote Control ■TUNER ■CD ■TAPE ■MD ■LD ■VCR 1/VCR 2/VCR ■CBSAT ■DVD ■D-TV