Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V1000 ZONE, Zone 2 Connections, ■Example of a system configuration and connections, •A video monitor for the second room, •An infrared emitter in the main room

1 86

Download 86 pages, 2.16 Mb

ZONE 2

You can make up a multi-room audio-video system with this unit. This feature enables you to set this unit to reproduce separate input sources in the main room and second room (Zone 2) with the supplied remote control in the second room.

Only analog signals are sent to the second room. For any source you want to listen to in the second room, you must connect the analog output jack from the source to the corresponding analog input jack on this unit.

Zone 2 Connections

To use the multi-room functions of this unit, you need the following additional equipment:

•An infrared signal receiver in the second room•An infrared emitter in the main room

This emitter transmits the infrared signals from the remote control in the second room to the main room (for example, to a CD player or LD player).

•An amplifier and speakers for the second room•A video monitor for the second room

OUT		IN		OUT		IN			REMOTE
OUT		IN		OUT		IN		CONTROL OUT

y

•Since there are so many ways to connect and use this unit in a multi-room installation, we recommend that you consult with the nearest authorized YAMAHA dealer or service center for the Zone 2 connections which will best meet your requirements.

•Some YAMAHA models are able to connect directly to the REMOTE CONTROL OUT jack of this unit. If you own these products, you may not need to use an infrared emitter. Up to 6 YAMAHA components can be connected as shown.

This unit

■Example of a system configuration and connections

			ZONE 2 VIDEO OUT
	Main room		ZONE 2 AUDIO OUT
	Main room		Second room
			Second room
			Amplifier	Video
				Video
				monitor
	DVD player	This unit	Infrared signal receiver
	(or other component)	This unit	Remote control
	(or other component)		Remote control
			(in the Zone 2 mode)
	Infrared emitter

OPERATION	ADVANCED

REMOTE CONTROL OUT

REMOTE CONTROL IN

English

61

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Installing Batteries in the Remote CONTROLS AND FUNCTIONS qREC OUT/ZONE wEFFECT eA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door sdf 1Infrared window 2TRANSMIT indicator 3STANDBY 4SYSTEM POWER 5Input selector buttons Using the Remote Control ■Handling the remote control Front Panel Display 1t indicator 2VIRTUAL indicator 3 g and o indicators 0c indicator 0qw e rt SPEAKER SETUP CONNECTIONS Connecting Audio Components Page Connecting Video Components ■About the video jacks and component jacks, respectively to make composite video connections. If both types of signal (U.S.A., Canada, Australia and Singapore models only) Connecting the Speakers Use speakers with the specified impedance shown on the rear panel of this unit ■Speaker cables A speaker cord is actually a pair of insulated cables running side by side. One of the cables is colored or ■Using the rear center speaker Rear center speaker placement Connecting the rear center speaker Setting up this unit for using the rear center speaker Connecting to an External Amplifier 5SUBWOOFER jack this unit 1MAIN jacks IMPEDANCE SELECTOR Switch ■VOLTAGE SELECTOR (China and general models only) Connecting the Power Supply Cords ■AC OUTLET(S) (SWITCHED) ON-SCREENDISPLAY (OSD) P01 CONCERT HALL SPEAKER MODE SETTINGS ADJUSTING THE SPEAKER OUTPUT LEVELS Using the Test Tone (TEST DOLBY SUR.) Use the test tone to balance the output levels of the 1,5 1Press TEST to output the test tone BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■BGV (background video) function Input Modes and Indications AUTO: In this mode, the input signal is automatically selected in the following ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program ■Virtual CINEMA DSP and SILENT CINEMA DSP –when the 6ch Stereo, DOLBY DIGITAL/Normal or DTS/ Normal program is selected; –when the sound effect is turned off; –when 6CH INPUT is selected as the input source; –when 96-kHzsampling digital signals are input to this unit; TUNING Automatic (or Manual) Tuning 3Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator goes off from the front panel display 1 Press INPUT l / h to select TUNER as the input Presetting Stations ■Automatically presetting stations (for FM stations) 1Press FM/AM to select the FM band 3Press and hold MEMORY (MAN’L/AUTO FM) for more than 3 seconds Automatic preset tuning options ■ Manually presetting stations 5 Press MEMORY (MAN’L/AUTO FM) while the You can also store up to 40 stations (8 stations x “MEMORY” indicator is flashing groups) manually Exchanging Preset Stations 2,4 1Tune in to preset station “E1” 2Press and hold PRESET/TUNING (EDIT) for more than 3 seconds 3Tune in to preset station “A5” by using the buttons on the front panel BASIC RECORDING SET MENU SET MENU 1/4 2 LOW FRQ TEST 1 SPEAKER SET (speaker mode 1B MAIN SP 1E LFE/BASS OUT 1F MAIN LEVEL 3L/R BALANCE (balance of the left and right main speakers) Control range: 10 steps for L/R Initial setting: 4HP TONE CTRL (headphone tone control) Control range (dB): –6to +3 8 INPUT MODE (initial input mode) Choices: AUTO, LAST Initial setting: AUTO AUTO 11 DTS LFE LEVEL This setting is effective only when this unit decodes DTS signals Control range (dB): –10to +10 12 6.1/ES AUTO Choices: ON, OFF 14 DISPLAY SET ■BLUE BACK > AUTO/OFF ■OSD SHIFT (OSD off-setposition) This setting is used to adjust the vertical position of the OSD ■DIMMER ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER REMOTE CONTROL FEATURES ■SOURCE SELECT k / n ■OPTN (option) area ■Zone 2 feature Each Component Control Area The YAMAHA code is factory set for the A, TUNER, MD/TAPE, CD ■Operating a tuner (TUNER area) ■Operating a CD player (CD area) TV/LD area ■Operating an MD recorder (MD/TAPE area) When the manufacturer code for your TV is set up in the both ■Operating a CD recorder (CD-Rarea) ■Operating an LD player (A area) ■Operating a DVD player (DVD area) ■Operating a VCR (VCR 1, VCR 2/DVR and V-AUXareas) ■Operating a TV/digital TV (D-TV/LDand PHONO areas) If you operate an LD player in the ■Operating a cable TV (CBL/SAT area) or satellite tuner (B area) ■Free area (OPTN area) Setting the Manufacturer Code •Press LEARN for at least 3 seconds, otherwise the learning process is started 3Press k / n to select the name of your component’s manufacturer If the component cannot be controlled with the remote / control, try setting another Programming a New Remote Control Function (Learn Feature) 1 Set 10KEY/DSP to 10KEY 2Press an input selector button, A or B to select a source component 4Press LEARN by using a ballpoint pen or similar object 7Repeat steps 5 and 6 to program additional functions 8Press LEARN again to exit from the learning mode 5Press the button for which you want to program the new function “LEARN” is displayed Using the Macro Feature please refer to the operation instruction for the connected component.) ■Operating the macro 1Set MACRO ON/OFF to ON 2Press a macro button •When you have finished using the Macro feature, set MACRO ON/OFF to OFF ■Programming a macro Changing the Source Name in the Macros, Renamed Source Names ZONE ■Special considerations when using DTS software For LDs or DVDs encoded with DTS Only 2-channelanalog audio signals may be sent to the second room, as follows: For CDs encoded with DTS DO NOT USE the Zone 2 feature for CDs encoded with DTS SOUND FIELD PROGRAM CINEMA DSP Programs ■For audio-videosources: Nos. 7 to Game This program adds a deep and spatial feeling to video game sounds TV SPORTS (group) 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Input source q/DTS Normal PRO LOGIC/Normal Analog, PCM MOVIE THEATER Programs ■Dolby Pro Logic + DSP sound field effect ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital Matrix 6.1/DTS ES + DSP sound field effect SOUND FIELD PROGRAM PARAMETER EDITING P05 ROCK CONCERT Digital Sound Field Parameter Descriptions ■INIT.DLY (initial delay) (P.INIT.DLY — for the presence sound field) Function: direct sound and the first reflection heard by the listener ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM.SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RC.DELAY (rear center delay) TROUBLESHOOTING English APPENDIX Page ■Tuner ■Remote control SPECIFICATIONS Page ■Remote Control ■TUNER ■CD ■MD ■CD-R ■ LD (A) ■ VCR ■ DVD ■ TV (TV/LD) ■CBL/SAT (CBSAT)