Yamaha RX-V1000 P05 ROCK CONCERT, Factory-setValue, Changing Parameter Settings, Resetting a Parameter to the, ■To reset all of the parameters to the factory-setvalues

Changing Parameter Settings

You can enjoy good quality sound with the factory-set parameters. Although you do not have to change the initial settings, you can change some of the parameters to better suit the input source or your listening room.

Adjustments should be made with the remote control.

y

•We recommended that you edit the parameter while using a video monitor. It is easier to see the video monitor than it is to see the front panel display.

	10KEY DSP	HALL 1	HALL 2		CHURCH	JAZZ CLUB
		1	2		3	4
3		ROCK			ENTER-	TV
		CONCERT	STADIUM		TAINMENT	SPORTS
		5	6		7	8
	6.1/ES	MONO	MOVIE		MOVIE	/DTS
		MOVIE	THEATER 1		THEATER 2	SUR.
		9	10		11	12
	CHP/INDEX		0		+10	+100
		A / B / C / D / E	PRESET
	+	TV INPUT	+		MUTE	+
	TV VOL		CH			VOLUME
	–	TV MUTE	–	EFFECT		–
			DISC
2						PARAMETER	1
	ON SCREEN LEVEL
4						SET MENU
	SLEEP	TEST
5

1 Set PARAMETER/SET	PARAMETER
MENU to PARAMETER.	SET MENU
2 Turn on the video monitor	ON SCREEN
and press ON SCREEN
repeatedly to select the
full display mode.

3Select a DSP program you want to adjust.

10KEY DSP HALL 1	HALL 2	CHURCH	JAZZ CLUB
1	2	3	4
ROCK		ENTER-	TV
CONCERT	STADIUM	TAINMENT	SPORTS
5	6	7	8
MONO	MOVIE	MOVIE	/DTS
MOVIE	THEATER 1	THEATER 2	SUR.
9	10	11	12
	0	+10	+100

Program No. Program name (group)

P05 ROCK CONCERT

Cursor	INIT.DLY	15ms
	LIVENESS	5
	REV.TIME		1.6s
	REV.DELAY	100ms
	REV.LEVEL	7%

Parameters

Example of ROCK CONCERT

SOUND FIELD PROGRAM PARAMETER EDITING

4Press k / n to select theparameter.5Press –/+ to change theparameter value.

y

•When you set the parameter to a value other than the factory- set value, an asterisk mark (*) appears by the parameter name on the video monitor.

6Repeat steps 3 to 5 above as necessary to change other program parameters.

Memory back-up

The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again.

Resetting a Parameter to theFactory-set Value■To reset some of the parameters to the factory-set values

Select the parameter you want to reset. Then press and hold – or + until the value temporarily stops at the factory-set value. The asterisk mark (*) by the parameter name disappears on the video monitor.

■To reset all of the parameters to the factory-set values

Use “9 PARAM. INI” on the SET MENU to reset all of the parameter values of all DSP programs within the selected group to the factory-set values (see page 42). This operation resets all of the parameter values of all DSP programs within that group to the factory-set values.

Notes

•The available parameters may be displayed on more than one OSD page for some of the programs. To scroll through pages, press k / n.

•You cannot change parameter values when “15 MEMORY GUARD” on the SET MENU is set to ON. If you want to change the parameter values, set “15 MEMORY GUARD” to OFF (see page 44).

INFORMATION ADDITIONAL

English

69