Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V1000 8Press LEARN again to exit from the learning mode, 7Repeat steps 5 and 6 to program additional functions, “LEARN” is displayed

1 86

Download 86 pages, 2.16 Mb

REMOTE CONTROL FEATURES

4Press LEARN by using a ballpoint pen or similar object.

“LEARN” and the selected component name appear alternately in the display window.

LEARN

7Repeat steps 5 and 6 to program additional functions.8Press LEARN again to exit from the learning mode.

LEARN

Note

•If you do not press any button within 30 seconds during steps 5 and 6, the learning process is canceled. If this happens, start over from step 4.

5Press the button for which you want to program the new function.“LEARN” is displayed.

	TV/LD-D	AUX-V	SYSTEM POWER	TRANSMIT
TITLE	1 VCR CBL/SAT	MD/TAPE TUNER	STANDBY	LEARN CLEAR NAME-RE
ENTER		R-CD		MACRO
INPUT 6CH	DVD	CD	PHONO	MACRO ON OFF

Notes

•It is also possible to program in the control area of this unit with 10KEY/DSP set to DSP. However, if you program functions in this area, you cannot control this unit and select a DSP program.

•Even if the batteries in the other remote control have enough power to transmit signals for operation, they may not have enough power to transmit signals to this remote control.

•When the remote controls are either too close together or too far apart, you may not be able to program this remote control.

•Direct sunlight interferes with infrared rays.•“ERROR” appears in the display window in the following circumstances:

–when pressing more than one button at once; or

–when MACRO ON/OFF is switched to another position.

6Press and hold the button on the other remote control that has the function you want to program into this remote control until “OK” appears in the display window.

	TV/LD-D	AUX-V	SYSTEM POWER	TRANSMIT
TITLE	1 VCR CBL/SAT	MD/TAPE TUNER	STANDBY	LEARN CLEAR NAME-RE
ENTER	2/DVR VCR	R-CD		MACRO
INPUT 6CH	DVD	CD	PHONO	MACRO ON OFF

Notes

•“NG” appears in the display window when programming has not been done correctly. In this case, start over from step 5.

•When the memory is full, “FULL” appears in the display

window, and this remote control cannot acquire any more functions. Clear unnecessary programmed functions to allow this remote control to acquire new functions.

56

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Installing Batteries in the Remote CONTROLS AND FUNCTIONS qREC OUT/ZONE wEFFECT eA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door sdf 1Infrared window 2TRANSMIT indicator 3STANDBY 4SYSTEM POWER 5Input selector buttons Using the Remote Control ■Handling the remote control Front Panel Display 1t indicator 2VIRTUAL indicator 3 g and o indicators 0c indicator 0qw e rt SPEAKER SETUP CONNECTIONS Connecting Audio Components Page Connecting Video Components ■About the video jacks and component jacks, respectively to make composite video connections. If both types of signal (U.S.A., Canada, Australia and Singapore models only) Connecting the Speakers Use speakers with the specified impedance shown on the rear panel of this unit ■Speaker cables A speaker cord is actually a pair of insulated cables running side by side. One of the cables is colored or ■Using the rear center speaker Rear center speaker placement Connecting the rear center speaker Setting up this unit for using the rear center speaker Connecting to an External Amplifier 5SUBWOOFER jack this unit 1MAIN jacks IMPEDANCE SELECTOR Switch ■VOLTAGE SELECTOR (China and general models only) Connecting the Power Supply Cords ■AC OUTLET(S) (SWITCHED) ON-SCREENDISPLAY (OSD) P01 CONCERT HALL SPEAKER MODE SETTINGS ADJUSTING THE SPEAKER OUTPUT LEVELS Using the Test Tone (TEST DOLBY SUR.) Use the test tone to balance the output levels of the 1,5 1Press TEST to output the test tone BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■BGV (background video) function Input Modes and Indications AUTO: In this mode, the input signal is automatically selected in the following ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program ■Virtual CINEMA DSP and SILENT CINEMA DSP –when the 6ch Stereo, DOLBY DIGITAL/Normal or DTS/ Normal program is selected; –when the sound effect is turned off; –when 6CH INPUT is selected as the input source; –when 96-kHzsampling digital signals are input to this unit; TUNING Automatic (or Manual) Tuning 3Press TUNING MODE (AUTO/MAN’L MONO) so that the “AUTO” indicator goes off from the front panel display 1 Press INPUT l / h to select TUNER as the input Presetting Stations ■Automatically presetting stations (for FM stations) 1Press FM/AM to select the FM band 3Press and hold MEMORY (MAN’L/AUTO FM) for more than 3 seconds Automatic preset tuning options ■ Manually presetting stations 5 Press MEMORY (MAN’L/AUTO FM) while the You can also store up to 40 stations (8 stations x “MEMORY” indicator is flashing groups) manually Exchanging Preset Stations 2,4 1Tune in to preset station “E1” 2Press and hold PRESET/TUNING (EDIT) for more than 3 seconds 3Tune in to preset station “A5” by using the buttons on the front panel BASIC RECORDING SET MENU SET MENU 1/4 2 LOW FRQ TEST 1 SPEAKER SET (speaker mode 1B MAIN SP 1E LFE/BASS OUT 1F MAIN LEVEL 3L/R BALANCE (balance of the left and right main speakers) Control range: 10 steps for L/R Initial setting: 4HP TONE CTRL (headphone tone control) Control range (dB): –6to +3 8 INPUT MODE (initial input mode) Choices: AUTO, LAST Initial setting: AUTO AUTO 11 DTS LFE LEVEL This setting is effective only when this unit decodes DTS signals Control range (dB): –10to +10 12 6.1/ES AUTO Choices: ON, OFF 14 DISPLAY SET ■BLUE BACK > AUTO/OFF ■OSD SHIFT (OSD off-setposition) This setting is used to adjust the vertical position of the OSD ■DIMMER ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER REMOTE CONTROL FEATURES ■SOURCE SELECT k / n ■OPTN (option) area ■Zone 2 feature Each Component Control Area The YAMAHA code is factory set for the A, TUNER, MD/TAPE, CD ■Operating a tuner (TUNER area) ■Operating a CD player (CD area) TV/LD area ■Operating an MD recorder (MD/TAPE area) When the manufacturer code for your TV is set up in the both ■Operating a CD recorder (CD-Rarea) ■Operating an LD player (A area) ■Operating a DVD player (DVD area) ■Operating a VCR (VCR 1, VCR 2/DVR and V-AUXareas) ■Operating a TV/digital TV (D-TV/LDand PHONO areas) If you operate an LD player in the ■Operating a cable TV (CBL/SAT area) or satellite tuner (B area) ■Free area (OPTN area) Setting the Manufacturer Code •Press LEARN for at least 3 seconds, otherwise the learning process is started 3Press k / n to select the name of your component’s manufacturer If the component cannot be controlled with the remote / control, try setting another Programming a New Remote Control Function (Learn Feature) 1 Set 10KEY/DSP to 10KEY 2Press an input selector button, A or B to select a source component 4Press LEARN by using a ballpoint pen or similar object 7Repeat steps 5 and 6 to program additional functions 8Press LEARN again to exit from the learning mode 5Press the button for which you want to program the new function “LEARN” is displayed Using the Macro Feature please refer to the operation instruction for the connected component.) ■Operating the macro 1Set MACRO ON/OFF to ON 2Press a macro button •When you have finished using the Macro feature, set MACRO ON/OFF to OFF ■Programming a macro Changing the Source Name in the Macros, Renamed Source Names ZONE ■Special considerations when using DTS software For LDs or DVDs encoded with DTS Only 2-channelanalog audio signals may be sent to the second room, as follows: For CDs encoded with DTS DO NOT USE the Zone 2 feature for CDs encoded with DTS SOUND FIELD PROGRAM CINEMA DSP Programs ■For audio-videosources: Nos. 7 to Game This program adds a deep and spatial feeling to video game sounds TV SPORTS (group) 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Input source q/DTS Normal PRO LOGIC/Normal Analog, PCM MOVIE THEATER Programs ■Dolby Pro Logic + DSP sound field effect ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital Matrix 6.1/DTS ES + DSP sound field effect SOUND FIELD PROGRAM PARAMETER EDITING P05 ROCK CONCERT Digital Sound Field Parameter Descriptions ■INIT.DLY (initial delay) (P.INIT.DLY — for the presence sound field) Function: direct sound and the first reflection heard by the listener ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM.SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RC.DELAY (rear center delay) TROUBLESHOOTING English APPENDIX Page ■Tuner ■Remote control SPECIFICATIONS Page ■Remote Control ■TUNER ■CD ■MD ■CD-R ■ LD (A) ■ VCR ■ DVD ■ TV (TV/LD) ■CBL/SAT (CBSAT)