Tuning Operations, Tuning off | Yamaha RX-V692 RX-V592 specs

RX-V592

TUNING OPERATIONS

Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).

	l6
20	l2
28	8
40	4
60	2
	0
	–dB

AUTOMATIC TUNING

1 Select the reception band (FM or AM) confirming it on the display.

	RX-V692
FM/AM	FM or	AM
	RX-V592
	or
2	RX-V692	RX-V592
TUNING
MODE
AUTO/	AUTO TUNING	AUTO

3

DOWN TUNING UP

To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once.

*If the station where tuning search stops is not the desired one, press again.

*If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method.

1		3	2
	MANUAL TUNING

		1 Select the reception band (FM or AM) confirming it on
		the display.
		the display.		RX-V692
				RX-V692
		FM/AM		FM or AM

or

2 TUNING MODE

Turn “AUTO

AUTO/	(TUNING)” off.

3 Tune to a desired station manually.

DOWN TUNING UP

* To continue tuning search, press and hold the button.

Note

If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality.

26

Image 28

Yamaha RX-V692 RX-V592 owner manual Tuning Operations, Select the reception band FM or AM confirming it on, Tuning off

Contents

RX-V692 RX-V592 Safety Instructions We Want You Listening For a Lifetime for US customers only FCC Information for US customers onlyFor US customers only Important Notice do not Modify this Unit Contents Features Speaker Configuration For Canadian Customers Battery replacement Profile of this Unit Digital Sound Field ProcessingDolby Pro Logic Surround Dolby Pro Logic Surround + DSP Speaker Setup Speaker ConfigurationSpeaker Placement Speaker Configuration Connections Connections with Other ComponentsOutput GND Video Audio OUT Video OUT A. model AC* Outlets Switched GND terminal For turntable use Connecting with a Dolby Digital AC-3 Decoder 6CH Discrete Output RX-V692 only Connecting Speakers Left Main speakers B Remote Control IN, OUT terminals How to Connect Impedance Selector switch Rear Surround Output terminalsMain Output terminals Center Output terminal Connecting the AM loop antenna Antenna ConnectionsGND terminal AM loop Controls and Their Functions RX-V692 Bass Treble Center Mode button Tuning DOWN/UP buttonVideo AUX terminals Memory indicator Auto Tuning indicatorTape Monitor indicator Stereo indicator Speaker Balance Adjustment Set to the OFF For 5 speaker configuration For 4 speaker configuration Adjust its level Basic Operations To turn off the powerProvided for RX-V692 only To Record a Source to Tape or MD Adjusting the Balance control Adjusting the Bass and Treble controlsUsing the Tone Bypass switch Selecting the Speaker system Tuning off Tuning OperationsSelect the reception band FM or AM confirming it on Preset Tuning Manual Preset Tuning Automatic Preset Tuning When the automatic preset tuning is finishedTo recall a preset station To store stations Exchanging Preset Stations Example Using Digital Sound Field Processor DSP Brief Overview of Digital Sound Field Programs Program Feature Concert Video Movie TheaterTV Sports Jazz Club To play a source with the digital sound field processor Adjustment of the Center Level Adjustment of the Rear Level Mm Movie Adjustment of Delay TimeTheater Setting the Sleep Timer To cancel the selected Sleep timeTo set the Sleep time 120 90 60 Remote Control Transmitter Basic Operations When the lid is openLid is opened Side panel Sleep timer key System Power and OFF keysReset button Reset button Master Volume up and down keys Learning NEW Control Functions When the lid is open Keys which can have three functions 1, 2, 3To use these keys Empty keys 1 About the marks shown on the remote control transmitter Using Operation Control Keys When the lid is closedOperation Except REC/PAUSE, A/B, DIR a and B To operate your VCR+10 Macro Operations When the lid is closed Setting the Macro switchPreset macro keys Switch Macro key On area a of keysOn area B of keys On area C of keys Learning a NEW Function Making a NEW Macro Memory back-up Clearing Learned Functions Trouble shooting guide To Clear All Learned FunctionsTo Clear a Learned Function Troubleshooting Specifications General Seccion DE AM