Manuals / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V692 RX-V592 Antenna Connections, GND terminal, Connecting the AM loop antenna

Models: RX-V692 RX-V592

1 51

Download 51 pages 56.58 Kb

Page 17

ANTENNA CONNECTIONS

●Each antenna should be connected to the designated terminals correctly, referring to the following diagram.

●Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.

Outdoor FM antenna

Outdoor AM antenna

Indoor FM antenna (included)

English

75-ohm/300-ohm antenna adapter

75-ohm coaxial cable

75-ohm/300-ohm antenna adapter

300-ohm feeder

	AM loop
GND	antenna
75Ω UNBAL.	(included)
75Ω UNBAL.
FM
ANT
GND
AM
ANT
PHONO

Ground

Connecting the AM loop antenna

1

2

3

➀

➂

➁

Orient so that the best reception is obtained.

*The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.

*The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.

GND terminal

For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Notes

●When connecting the indoor FM antenna, insert its connector into the FM ANT

terminal firmly.

●If you need an outdoor

FM antenna to improve FM reception quality, either

300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable.

15

Image 17

Yamaha RX-V692 RX-V592 owner manual Antenna Connections, GND terminal, Connecting the AM loop antenna

Contents

RX-V692 RX-V592 Safety Instructions FCC Information for US customers only We Want You Listening For a Lifetime for US customers onlyFor US customers only Important Notice do not Modify this UnitContents Speaker Configuration FeaturesFor Canadian Customers Battery replacement Digital Sound Field Processing Profile of this UnitDolby Pro Logic Surround Dolby Pro Logic Surround + DSPSpeaker Configuration Speaker SetupSpeaker Placement Speaker ConfigurationConnections with Other Components ConnectionsOutput GND Video Audio OUT Video OUT A. modelGND terminal For turntable use AC* Outlets Switched6CH Discrete Output Connecting with a Dolby Digital AC-3 DecoderRX-V692 only Left Main speakers B Connecting SpeakersHow to Connect Remote Control IN, OUT terminalsRear Surround Output terminals Impedance Selector switchMain Output terminals Center Output terminalAntenna Connections Connecting the AM loop antennaGND terminal AM loopRX-V692 Controls and Their FunctionsTreble BassVideo AUX terminals Tuning DOWN/UP buttonCenter Mode button Auto Tuning indicator Memory indicatorTape Monitor indicator Stereo indicatorSet to the OFF Speaker Balance AdjustmentFor 4 speaker configuration For 5 speaker configurationAdjust its level Provided for RX-V692 only To turn off the powerBasic Operations To Record a Source to Tape or MD Adjusting the Bass and Treble controls Adjusting the Balance controlUsing the Tone Bypass switch Selecting the Speaker systemSelect the reception band FM or AM confirming it on Tuning OperationsTuning off Manual Preset Tuning Preset TuningWhen the automatic preset tuning is finished Automatic Preset TuningTo recall a preset station To store stationsExample Exchanging Preset StationsBrief Overview of Digital Sound Field Programs Using Digital Sound Field Processor DSPMovie Theater Program Feature Concert VideoTV Sports Jazz ClubTo play a source with the digital sound field processor Adjustment of the Rear Level Adjustment of the Center LevelTheater Adjustment of Delay TimeMm Movie To cancel the selected Sleep time Setting the Sleep TimerTo set the Sleep time 120 90 60Basic Operations When the lid is open Remote Control TransmitterLid is opened Side panelSystem Power and OFF keys Sleep timer keyReset button Reset button Master Volume up and down keysKeys which can have three functions 1, 2, 3 Learning NEW Control Functions When the lid is openTo use these keys Empty keys 1Operation Using Operation Control Keys When the lid is closedAbout the marks shown on the remote control transmitter +10 To operate your VCRExcept REC/PAUSE, A/B, DIR a and B Setting the Macro switch Macro Operations When the lid is closedPreset macro keys SwitchOn area a of keys Macro keyOn area B of keys On area C of keysLearning a NEW Function Memory back-up Making a NEW MacroTo Clear a Learned Function Trouble shooting guide To Clear All Learned FunctionsClearing Learned Functions Troubleshooting Specifications General Seccion DE AM