AUTO SETUP

■Troubleshooting for auto setup procedure

Before auto setup

Error message

Cause

Remedy

 

 

 

Connect MIC!

Optimizer microphone is not connected.

• Connect the supplied optimizer microphone to the

 

 

OPTIMIZER MIC jack on the front panel.

 

 

 

Unplug HP!

Headphones are connected.

• Unplug the headphones.

 

 

 

Errors during auto setup

Press SELECT to display detailed information about individual errors. Press j / i to switch between error messages.

Error message

Cause

Remedy

 

 

 

E-1:NO FRONT SP

Front L/R channel signal(s) is (are) not

• Select the front speakers with SPEAKER A or B.

 

detected.

• Check the front left and right speaker connections.

 

 

 

E-2:NO SURR.SP

A surround channel signal is not detected.

• Check the surround speaker connections.

 

 

 

E-3:NO PRES. SP

A presence channel signal is not detected.

• Check the presence speaker connections.

 

 

 

E-4:SBR->SBL

Only right surround back channel signal is

• Connect the surround back speaker to the LEFT

 

detected.

SURROUND BACK SPEAKERS terminal if you

 

 

only have one surround back speaker.

 

 

 

E-5:NOISY

Background noise is too loud.

• Try the auto setup procedure in a quiet environment.

 

 

• Turn off noisy electric equipment like air conditioners

 

 

(etc.) or move them away from the optimizer

 

 

microphone.

 

 

 

E-6:CHECK SURR.

Surround back speaker(s) is (are) connected,

• Connect surround speakers when you use (a)

 

though surround L/R speakers are not.

surround back speaker(s).

 

 

 

E-7:NO MIC

The optimizer microphone was unplugged

• Do not touch the optimizer microphone during the

 

during the auto setup procedure.

auto setup procedure.

 

 

 

E-8:NO SIGNAL

The optimizer microphone does not detect test

• Check the microphone setting.

 

tones.

• Check the speaker connections and placement.

 

 

 

E-9:USER CANCEL

The auto setup procedure was cancelled due to

• Perform the auto setup procedure again. Do not adjust

 

user activity.

VOLUME (etc.) during the auto setup procedure.

 

 

 

E-10:OTHER ERROR

A DSP communication error or hangup

• Perform the auto setup procedure again.

 

occurred.

 

 

 

 

Warnings after auto setup

Press j / i to display detailed information about individual warnings.

Warning message

Cause

Remedy

 

 

 

W-1:OUT OF PHASE

Speaker polarity is not correct. This message

• Check the speaker connections for proper polarity

 

may appear depending on the speakers even

(+ or –).

 

when the speakers are connected correctly.

 

 

 

 

W-2:OVER 24m

The distance between the speaker and the

• Bring the speaker closer to the listening position.

(80ft)

listening position is over 24 m (80 ft).

 

 

 

 

 

 

W-3:LEVEL ERROR

The difference of volume level among speakers

• Readjust the speaker installation so that all speakers

 

is excessive. (No level correction is made.)

are set in locations with similar conditions.

 

 

• Check the speaker connections.

 

 

• Use speakers of similar quality and efficiency.

 

 

• Adjust the output volume of the subwoofer.

 

 

 

•If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again.

•If warning W-1 appears, corrections are made, but they may not be optimal.

•If warning W-2 or W-3 appears, no corrections are made.

•If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center.

30