Troubleshooting
■XM Satellite Radio
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel display. In this case, read the cause and follow the corresponding remedies.
Status message | Cause | Remedy | See | |
page | ||||
|
|
| ||
CHECK ANTENNA | The XM | Check XM | ||
| not connected to the XM jack of this unit | and orient for the best reception level. |
| |
| or do not work properly. |
|
| |
|
|
|
| |
UPDATING | The XM user encryption code is being | Wait until the encryption code is updated. | — | |
| updated. |
|
| |
|
|
|
| |
NO SIGNAL | The signal is too weak. | Adjust the orientation of the XM | ||
|
| best reception level. |
| |
|
|
|
| |
LOADING | It takes longer than four seconds for audio | Wait until the decoding process has finished. | — | |
| or text data to be decoded. |
|
| |
|
|
|
| |
OFF AIR | The XM Satellite Radio channel you | Check the channel number again or select another | — | |
| selected is not currently broadcasting any | XM Satellite Radio channel. |
| |
| signals. |
|
| |
|
|
|
| |
<XM> - - - | The Channel Station ID (SID) is no longer |
|
| |
| available. |
|
| |
|
|
|
| |
- - | No artist name or song title is available. |
|
| |
|
|
|
| |
<CAT> - - - | No channels are available for the selected | Select another channel category by pressing | ||
| category. | 4CATEGORY on the front panel (or |
| |
|
| l/ hon the remote control) repeatedly. |
| |
|
|
|
|
■Remote control
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
The remote control | Wrong distance or angle. | The remote control will function within a maximum | ||
does not work or |
| range of 6 m (20 ft) and no more than 30 degrees off- |
| |
function properly. |
| axis from the front panel. |
| |
|
|
|
| |
| Direct sunlight or lighting (from an | Reposition this unit. | — | |
| inverter type of fluorescent lamp, etc.) is |
|
| |
| striking the remote control sensor of this |
|
| |
| unit. |
|
| |
|
|
|
| |
| The batteries are weak. | Replace all batteries. | — | |
|
|
|
| |
| The operation mode selector is set | Set the operation mode selector correctly. | — | |
| incorrectly. | When operating this unit, set it to the KAMP |
| |
|
| position. |
| |
|
| When operating the component selected by the input |
| |
|
| selector button, set it to the KSOURCE position. |
| |
|
| When operating the TV set in the DTV or PHONO |
| |
|
| area, set it to the KTV position. |
| |
|
|
|
| |
| The remote control code was not correctly | Set the remote control code correctly using “List of | ||
| set. | remote control codes” at the end of this manual. |
| |
|
|
|
| |
|
| Try setting another code of the same manufacturer | ||
|
| using “List of remote control codes” at the end of this |
| |
|
| manual. |
| |
|
|
|
| |
| The ID code of the remote control and the | Match the remote control ID of this unit with the | ||
| remote control ID of this unit do not | corresponding remote control ID code. |
| |
| match. |
|
| |
|
|
|
|
INFORMATION | ADDITIONAL |
|
|
English