Yamaha SPX2000 - page 70

70 SPX2000—Owner’s Manual

■Fine parameters

Effect list

■Basic parameters

■Fine parameters

Parameter name Range Explanation

MIX BAL. 0—100% Balance between the original sound and effect sound. At a setting of 0% only the original sound

will be output; at a setting of 100% only the effect sound will be output.

OUT LVL 0—100% Output level after the original sound and effect sound have been mixed.

Decrease this value if you want to lower the output. At a setting of 0% there will be no output.

HPF Thru, 21.2 Hz—8.00 kHz

A ﬁlter that cuts the low-frequency portion of the effect. Frequency components lower than the

frequency speciﬁed here will be cut. With a setting of Thru this ﬁlter will do nothing. This ﬁlter

does not affect the original sound.

LPF 50.0 Hz—16.0 kHz, Thru

A ﬁlter that cuts the high-frequency portion of the effect. Frequency components above the fre-

quency speciﬁed here will be cut. With a setting of Thru this ﬁlter will do nothing. This ﬁlter does

not affect the original sound.

REV/FLG 0—100% (Reverb + Flanger only) Balance between the reverb and ﬂanger. A setting of 0% outputs only the

reverb; a setting of 100% outputs only the ﬂanger.

REV.BAL 0—100% (Reverb → Flanger only) Amount of ﬂanger. Raising this value will strengthen the ﬂanger effect. At

a setting of 0% only reverb will be heard.

SYNC ON, OFF

Switches tempo synchronization on/off. If this is ON, the speed of modulation will synchronize to

the tempo synchronization source speciﬁed by “TEMPO SOURCE” (page 23). The NOTE value

will be set to the synchronized tempo value.

NOTE *a

*a.

This parameter is used for tempo synchronization. If SYNC is ON, the FREQ. value will be set

according to this value and TEMPO. If SYNC is OFF, this value is ignored.

TEMPO 25—300 This parameter is used for tempo synchronization. If SYNC is ON, the FREQ. value will be set

according to this value and NOTE. If SYNC is OFF, this value is ignored.

No. Effect name FREQ. DEPTH MOD.DLY FB.GAIN WAVE REV TIME HI.RATIO INI.DLY DIFF. DENSITY

14 REVERB FLANGE 1.10 Hz 80% 1.2 ms +10% Sine 2.4 s 0.4 0.1 ms 5 95%

87 REV+FLANGE 0.25 Hz 88% 0.3 ms –84% Tri 1.9 s 0.7 2.4 ms 10 100%

No. Effect name MIX BAL. OUT LVL HPF LPF REV/FLG REV.BAL SYNC NOTE TEMPO

14 REVERB FLANGE 76% 100% Thru 4.25 kHz 60% OFF —

87 REV+FLANGE 100% 100% Thru Thru 67% OFF —

Contents

Main SPX2000Owners Manual PRECAUTIONS Backup battery Do not open Do not insert your ngers or hand in any gaps or openings on the device. Do not place the device in an unstable position where it might accidentally fall over. FCC INFORMATION (U.S.A.) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) IMPORTANT SAFETY INSTRUCTIONS CAUTION WARNING Table of contents Features of the SPX2000 Software features Hardware features Controlling the SPX2000 from your computer Parts and their functions Front panel DA4681LK P H N O 2 357 9 0 B E I J MFC G Page Rear panel R S T W XYU V ZQ \ [ Operation Basic operation Z \ 1 Select the input signal Adjust the input level 1 Three banks K Switch the effect on/off J H Editing an effect K J H F Select a parameter Edit the parameter Setting the tempo Effects and tempo synchronization 2 3 Check the edited effect N Store the effect Undoing the previous operation Other functions 3 +, 4 3 Changing the display back- ground color LCD BACK=YELLOW REV-X LARGE HALL LCD BACK=GREEN Selecting the word clock source CLOCK SOURCE INT96kHz About word clock Selecting the input source Restricting operation of the SPX2000 INPUT SOURCE *ANALOG DIGITAL OPERATION LOCK *OFF 1 2 3 20 3 4 Erasing an effect U01 CLEAR? PUSH INC Selecting the port for MIDI transmission/reception MIDI PORT GENERAL = MIDI Switching MIDI OUT/THRU Selecting the MIDI transmission/ reception channel MIDI OUT SETUP *OUT THRU Editing the MIDI program change table MIDI PGM CHANGE TBL A:PGM 1=P01 Transmitting SPX2000 data to another device Selecting the tempo synchroni- zation source Enabling/disabling MIDI mes- sage reception Initializing the SPX2000 Effects Effects PRESET bank CLASSIC bank Reverb REV-X (PRESET bank) Page Reverb (CLASSIC bank) Stereo Reverb (PRESET bank) SPX2000Owners Manual 31 Reverb (PRESET bank) Early reections: INI.DLY Reverberation: REV TIME, HI.RATIO, LO.RATIO, DIFF., DENSITY, E/R DLY Gating: GATE LVL, ATTACK, HOLD, DECAY Overall effect sound: E/R BAL. Page SPX2000Owners Manual 33 Reverb & Gate (CLASSIC bank) Reverberation: REV TIME, HI.RATIO, DELAY Gating: TRG. LVL, HOLD, RELEASE, MIDI TRG What is a Gate? ER Early Reection Early Reection, Gate Reverb, Reverse Gate (PRESET bank) Page ER Early Reection, Gate Reverb, Reverse Gate (CLASSIC bank) Delay, Echo Time Mono Delay (PRESET bank) These are basic delay effects. A monaural delayed sound will follow the original sound. Delay sound: DELAY, FB.GAIN, HI.RATIO SPX2000Owners Manual 39 Stereo Delay (PRESET bank) Modulation Delay (PRESET bank) Page SPX2000Owners Manual 43 Delay L,C,R (PRESET bank) Delay sound: DELAY L, DELAY C, DELAY R, FB.DLY, FB.GAIN, HI.RATIO Echo (PRESET bank) SPX2000Owners Manual 45 Delay L,R, Stereo Echo (CLASSIC bank) Modulation Flanger (PRESET bank) Page SPX2000Owners Manual 49 Phaser (PRESET bank) Modulation signal: FREQ., DEPTH, PHASE Phase shift: FB.GAIN, OFFSET, STAGE Filter/equalizer: LSH G, LSH F, HSH G, HSH F Stereo Flanger, Stereo Phasing (CLASSIC bank) SPX2000Owners Manual 51 Chorus (PRESET bank) Modulation signal: FREQ., AM DEPTH, PM DEPTH, WAVE Effect sound: MOD.DLY Symphonic (PRESET bank) Modulation signal: FREQ., DEPTH, WAVE Phase shift: MOD.DLY SPX2000Owners Manual 53 Tremolo (PRESET bank) This effect cyclically varies the volume, producing amplitude modulation (AM). Modulation signal: FREQ., DEPTH, WAVE Chorus, Tremolo (CLASSIC bank) Symphonic (CLASSIC bank) SPX2000Owners Manual 55 Auto Pan (PRESET bank) This effect cyclically moves the pan position of the sound. Modulation: FREQ., DEPTH, WAVE, DIR. Pan (CLASSIC bank) Modulation Filter (PRESET bank) Ring Modulation (PRESET bank) Dynamic Filter (PRESET bank) SPX2000Owners Manual 59 Dynamic Flanger (PRESET bank) Modulation signal: SOURCE Effect sound: SENSE, OFFSET, FB.GAIN Dynamic Phaser (PRESET bank) SPX2000Owners Manual 61 Pitch Change High Quality Pitch (PRESET bank) This is a typical pitch change effect. Effect sound: PITCH, FINE, DELAY, FB.GAIN, MODE Dual Pitch (PRESET bank) SPX2000Owners Manual 63 Pitch Change A, D (CLASSIC bank) Pitch Change B (CLASSIC bank) Pitch Change C (CLASSIC bank) Composite effects Distortion Flanger (PRESET bank) Distortion Delay (PRESET bank) Page Reverb + Chorus (PRESET bank) Reverb Chorus (PRESET bank) Chorus: FREQ., AM DEPTH, PM DEPTH, MOD.DLY, WAVE Balance of reverb and chorus: REV/CHO, REV.BAL Reverb + Flanger (PRESET bank) Reverb Flanger (PRESET bank) Page SPX2000Owners Manual 71 Reverb + Symphonic (PRESET bank) Reverb Symphonic (PRESET bank) Symphonic: FREQ., DEPTH, MOD.DLY, WAVE Balance of reverb and symphonic: REV/SYM, REV.BAL Reverb Pan (PRESET bank) This applies reverb to the original sound and then applies panning. Pan: FREQ., DEPTH, WAVE, DIR. Balance of reverb and pan: REV.BAL Delay + Early Reections (PRESET bank) Delay Early Reections (PRESET bank) Page SPX2000Owners Manual 75 Delay + Reverb (PRESET bank) Delay Reverb (PRESET bank) Tempo synchronization: SYNC, NOTE L, NOTE R, NOTE FB, TEMPO Page SPX2000Owners Manual 77 Freeze These are sampling effects that let you record the input signal and play it back. Freeze (PRESET bank) Freeze A (CLASSIC bank) Recording: REC MODE, TRG. DLY, RECORD Playback: PLAY, START, END Recording trigger: INP. TRG Freeze B (CLASSIC bank) AUTO: Use an input signal to trigger the recording MANUAL: Record manually Freeze recording Play back the sample manually Use an input signal to trigger the playback Use a MIDI message to trigger the playback Playback options Freeze Playback Other effects Multi Filter (PRESET bank) SPX2000Owners Manual 83 Multi-band Dynamics Processor (PRESET bank) Page Rotary Speaker (PRESET bank) Distortion (PRESET bank) SPX2000Owners Manual 87 Amp Simulator (PRESET bank) MIDI 5 Preparations for using MIDI 1 2 MIDI data format 1.1 CHANNEL MESSAGE 1.2 SYSTEM REALTIME MESSAGE 1.3 EXCLUSIVE MESSAGE 1.3.1 Bulk dump 1.3.2 Parameter Change 2.4 PROGRAM CHANGE (Cn) 2.5 TIMING CLOCK (F8) 2.6 ACTIVE SENSING (FE) 2.7 SYSTEM RESET (FF) 2.8 SYSTEM EXCLUSIVE MESSAGE (F0) 2.8.1.3 System Setup Data Bulk Dump request Format This bulk-dumps the data of the specied effect. CHECK SUM 0eeeeeee ee ee=(Invert(L+...de) +1)&0x7F The second and third byte of DATA NAME specify the program num- ber. For reception by the SPX2000, only USER 1-99 or EDIT BUFFER are valid. (120-220, 256) 2.8.2.2 Parameter request (Edit Buffer) 2.8.2.3 Parameter change (System Setup Memory) This message modies the value of a parameter in system setup memory. 2.8.2.4 Parameter request (System Setup Memory) 2.8.2.5 Parameter change (System Backup Memory) 2.8.2.10 Parameter change (Function call : Program clear) 2.8.2.11 Parameter change (Function call : Undo) 2.8.2.12 Parameter change (Function call : Compare) 2.8.2.13 Parameter change (Function call : Event Effect) 2.8.2.15 Parameter request (Function call: attribute(Protect)) 2.8.2.17 Parameter request (Function call: LCD Back Color) 2.8.2.18 Parameter change (Remote Meter) 2.8.2.19 Parameter request (Remote Meter) MIDI Control Change Parameter Assignment Table PRESET bank CLASSIC bank SPX2000Owners Manual 97 Error message list Troubleshooting Specications General Specications Input/Output Characteristics Analog Input Characteristics Control I/O Characteristics Analog Output Characteristics Digital Input Characteristics Electrical Characteristics Page Block Diagram Dimensions Unit: mm Index Page Page Page WB42190 HEAD OFFICE CANADA U.S.A. MEXICO