York D1EE 060 Utilities Entry Data, Clearances, Front View, Unit Base With Rails, Rear View

035-12046-003-A-0204

￿￿(Direct￿￿-Drive Units)

FIELD-SUPPLIED

BLOWER

DISCONNECT SWITCH

ACCESS

LOCATION

CONTROL

FILTER ACCESS

BOX ACCESS

OUTDOOR

COIL

COMPRES-

SOR

FRONT VIEW

ELECTRIC

HEAT

￿￿￿￿

ACCESS

￿￿“ PVC FEMALE

￿￿

￿￿

￿

COND. DRAIN

(See Detail ”A")

￿￿￿￿

￿￿￿￿

￿

￿

￿￿￿

￿

￿

￿

DUCT COVERS - Units are shipped with all air duct

A, B

openings covered.

WIRING ENTRY

For side duct applications;

(See Detail “B”)

1.Remove and discard the supply and return air duct

covers.

2.Connect ductwork to duct flanges on the rear of the

unit.

For bottom duct applications;

￿￿￿

￿

￿￿

￿

￿￿

UNIT BASE WITH RAILS

1. Remove the side supply air duct cover to gain

BOTTOM SUPPLY &

access to the bottom supply air knockout panel.

Shown separately to illustrate bottom

RETURN AIR OPENINGS

2. Remove and discard the bottom knockout panel.

duct openings and power connection

(SEE NOTE)

￿￿￿

locations.

3. Replace the side duct cover.

B - POWER WIRING ENTRY

NOTE: For curb-mounted units, refer to the

4. With filter section access panel removed from the

duct hanger dimensions of the curb for the

A - CONTROL WIRING ENTRY

proper size of the supply and return air

unit, remove and discard the bottom return air

duct connections.

knockout panel.

CLEARANCES

5. Replace the filter access panel.

Front

24"

All dimensions are in inches. They are sub-

12" (Less Economizer)

ject to change without notice. Certified di-

36" (With Economizer

mensions will be provided upon request.

Back

￿￿

or Fixed Air/Motorized

￿

UTILITIES ENTRY DATA

Air Damper)

￿￿￿￿

￿￿￿￿￿￿￿

￿￿￿￿￿3

Left Side (Filter Access)

24" (Less Economizer)

KNOCKOUT

36" (With Economizer)

HOLE

SIZE

USED FOR

Right Side (Cond. Coil)

24"

(DIA.)

Control Wiring

Below Unit1

0"

Above Unit2

72" (For Condenser Air

A

7/8" *

(Side or

Bottom)**

Discharge)

Power Wiring

NOTE:

B

2" *

(Side or

Units and ductwork are approved for zero clearance to combustible

Bottom)

materials when equipped with electric heaters.

1 Units may be installed on combustible floors made from wood or

*Knockouts in the bottom of the unit can be

REAR VIEW

class A, B or C roof covering material. (Applicable in USA only).

located by the slice in the insulation.

**Do not remove the 2" knockout ring.

2 Units must be installed outdoors. Overhanging structures or shrubs

SIDE SUPPLY AND RETURN

should not obstruct the outdoor coil nor the fan outlet.

AIR OPENINGS

AIR FLOW LEGEND

￿￿￿￿

￿￿￿￿

RETURN AIR

SUPPLY AIR

￿￿

￿￿￿￿

￿￿

￿￿￿

￿￿“

CONDENSATE￿￿￿￿

DRAIN

(must be trapped)

OUTDOOR AIR

OUTDOOR AIR

￿￿￿￿

B

(Economizer)

￿￿￿￿

￿￿￿￿

A

￿￿￿

	DIMENSION “A”
	FIXED
	OUTDOOR	12		“A”	￿￿￿
DETAIL “A”	AIR DAMPER	￿￿	￿	DETAIL “B”
	MOTORIZED
UNIT WITH ECONOMIZER RAIN HOOD	DAMPER		￿	UNIT WITH FIXED OUTDOOR
				AIR/MOTORIZED DAMPER RAIN HOOD

FIG. 5 - DIMENSIONS & CLEARANCES - 3 - 5 TONS

Unitary Products Group 7