York D2EG 048, D3EG 036, D2EG 060 Enthalpy Set Point Adjustment, Physical Data

035-14832-003-A-0204

NOTE: Install filters so that “Air Flow” arrows point toward the unit.

8.Install filter cover over the end of the hood with one screw (center of hood), securing filters into position.

CAUTION: When proceeding with Steps 9 and 10, extreme care must be exercised while turning both the set point and minimum position adjusting screws to prevent twisting them off.

9.The enthalpy set point for the dampers may now be set by selecting the desired set point from graph in Figure 8. For a single enthalpy economizer, carefully turn the set point ad- justing screw to the “A”, “B”, “C” or “D” setting correspond- ing to the lettered curve. For a dual enthalpy economizer, carefully turn the set point adjusting screw fully clockwise past the “D” setting.

10.To check that the damper blades move smoothly without binding, carefully turn the minimum position adjusting screw fully clockwise and then energize and de-energize terminals “R” to “G”. With terminals “R” to “G” energized, turn the minimum position screw counterclockwise until the desired minimum position has been attained.

11. Replace the filter section access panel. FIG. 8 - ENTHALPY SET POINT ADJUSTMENT

TABLE 4 - PHYSICAL DATA

	MODELS		DEG
		036	048	060
EVAP.	CENTRIFUGAL BLOWER (Dia. x Wd. in.)	12 x￿￿10	12 ￿x￿10	12 x 10
	FAN MOTOR HP (Direct-Drive)			1
BLOWER
	FAN MOTOR HP (Belt-Drive)	1.5	1.5	1.5
EVAP.	ROWS DEEP	3	3	3
	FINS PER INCH	13	13	13
COIL
	FACE AREA (Sq. Ft.)	3.6	4.3	5.1
COND.	PROPELLER DIA. (in.)	22￿￿	22￿￿	22￿￿
	FAN MOTOR HP
FAN		4,500	4,200	4,500
	NOM. CFM TOTAL
COND.	ROWS DEEP	2	2	2
	FINS PER INCH	18	18	18
COIL
	FACE AREA (Sq. Ft.)	17.1	17.1	17.1
AIR	QUANTITY PER UNIT (14" x 20" x 1")	2	2	2
FILTERS	QUANTITY PER UNIT (14" X 25" X 1")	1	1	1
(SEE NOTE)	TOTAL FACE AREA (sq. ft.)	6.3	6.3	6.3
CHARGE	REFRIGERANT 22 (lbs./oz.)	9/12	9/8	9/8
COMPRESSOR	QUANTITY PER UNIT (HERMETIC TYPE)	1 / RECPT	1 /RECPT	1 / SCROLL

NOTE: Filter racks are adapted for 1" or 2" thick filters.

WEIGHTS (LBS)

Basic Unit	3 Ton	615
	4 Ton	655
(Nom. Max.)
	5 Ton	680
OPTIONS / ACCESSORIES
Economizer		50
Motorized Outdoor		26
Air Damper
Barometric Relief/Fixed		10
Outdoor Air Intake Damper
Roof Mounting Curb		92
Belt-Drive Blower		5

TABLE 5 - SUPPLY AIR PERFORMANCE - 3, 4, & 5 TON w/Direct-Drive Blower

GAS HEAT VALUES SHOWN @ 230/460/575 VOLTS - Side Duct Connections

MODEL	MOTOR						Available External Static Pressure - IWG*
		0.20		0.30		0.40		0.50		0.60		0.70				0.80			0.90			1.00
DEG	SPEED
		CFM	Watts	CFM	Watts	CFM	Watts	CFM	Watts	CFM	Watts	CFM	Watts		CFM		Watts		CFM	Watts		CFM	Watts
	HI	-	-	-	-	1699	825	1650	785	1570	755	1430		725		1360		700	1280		680	1180		655
036	MED	1684	800	1631	780	1582	750	1524	720	1410	690	1324		650		1260		630	1185		610	1100		590
	LOW	1487	710	1464	690	1421	670	1367	650	1315	620	1246		605		1185		590	1110		570	1020		545
	HI	1996	960	1933	936	1868	910	1795	880	1722	845	1635		820		1544		790	1419		765	1300		740
048	MED	1804	838	1765	810	1714	785	1650	765	1589	735	1508		705		1407		675	1306		645	1195		625
	LOW	1681	760	1640	738	1604	715	1541	695	1490	670	1416		645		1337		620	1230		595	1120		575
	HI	2400	1155	2338	1125	2274	1095	2167	1045	2096	1010	1990		980		1887		945	1771		905	1629		855
060	MED	2290	1105	2214	1065	2145	1030	2071	990	1990	950	1911		920		1828		885	1724		835	1604		798
	LOW	2150	1020	2100	990	2029	950	1965	910	1905	880	1816		838		1724		800	1644		770	1531		710

NOTE: FOR 208 VOLTS, MULTIPLY VALUES BY 0.95.

*INCLUDES ALLOWANCES FOR A WET EVAPORATOR COIL, 1" FILTERS, AND THE GAS-FIRED HEAT EXCHANGERS. REFER TO TABLE 8 FOR RESISTANCE VALUES ON APPLICATIONS OTHER THAN GAS/ELECTRIC UNITS WITH SIDE DUCT AIRFLOWS.

8 Unitary Products Group