Manuals / York / Household Appliance / Air Conditioner

York DY 060 Unit Dimensions Rear View, Minimum Clearances, Hole, Opening Size Dia, Used For

Models: DY 048 DY 060

1 36

Download 36 pages 25.65 Kb

Page 28

FIGURE 7 - UNIT DIMENSIONS (REAR VIEW)

343615-YTG-B-0308

FIGURE 7 - UNIT DIMENSIONS (REAR VIEW)

Filter Access
Blower Motor Access
Dot Plugs
Field-Supplied Disconnect
Switch Location
Mounting Bracket for
Disconnect Switch	A,B
(Field Supplied)	A,B
	Wiring Entry	Control Box Access
	(See Detail “B”)	Control Box Access

Disconnect Switch Location and Motor Access Panel for Unit with “Belt-Drive” Option

FIGURE 8 - DISCONNECT/BLOWER ACCESS LOCATION TABLE 28: UTILITIES ENTRY

HOLE	OPENING SIZE (DIA.)	USED FOR
A	7/8” KO1	Control Wiring2		Side
A	7/8” KO1	Control Wiring2		Bottom
				Bottom

B	2” KO1	Power Wiring		Side

				Bottom
				Bottom

C	1-5/8” KO	Gas Piping (Front)
D	1-1/2” KO	Gas Piping (Bottom)

1.Opening in the bottom to the unit can be located by the side in the insulation.

2.Do not remove the 2” knockout ring.

TABLE 29: MINIMUM CLEARANCES

	LOCATION	CLEARANCE
	Front	24” (Cooling/Electric Heat)
	Front	32” (Gas Heat)
		32” (Gas Heat)

	Rear	12” (Less Economizer)
	Rear	36” (With Economizer or Fixed
		Air/Motorized Damper)

	Left Side (Filter Access)	24” (Less Economizer)
	Left Side (Filter Access)	36” (With Economizer)
		36” (With Economizer)

	Right Side (Cond. Coil)	24”
	Below Unit1	0”
	Above Unit2	72” (For
	Above Unit2	Condenser Air Discharge)
		Condenser Air Discharge)

1.Units may be installed on combustible floors made from wood or class A, B, or C roof covering material.

2.Units must be installed outdoors. Overhanging struc- tures or shrubs should not obstruct condenser air dis- charge outlet.

28	Johnson Controls Unitary Products

Image 28

York DY 060, DY 048 warranty Unit Dimensions Rear View, Minimum Clearances, Hole, Opening Size Dia, Used For

Contents

TECHNICAL GUIDE AIR CONDITIONERSDESCRIPTION DYLIST OF FIGURES TABLE OF CONTENTSLIST OF TABLES 3-5Ton Sunline Magnum Model Number Nomenclature PRODUCT NOMENCLATURED Y 048 N04 A 2 A AA 2 0 1 2 4 A FEATURES Electric/Electric and Heat Pump Gas/ElectricFIGURE 1 - UNIT CUTAWAY FACTORY-INSTALLEDOPTIONS FIELD-INSTALLEDACCESSORIES TABLE 2 GAS HEAT RATINGS1 TABLE 1 CAPACITY RATINGS - ARI 210/2401TABLE 3 2 STAGE GAS HEAT RATINGS UNIT DESCRIPTION / MODEL UNIT DESCRIPTION / MODEL UNIT DESCRIPTION / MODEL UNIT DESCRIPTION / MODEL UNIT DESCRIPTION / MODEL CONFIGURATION CONFIGURATIONUNIT DESCRIPTION / MODEL DY060 / 5 TonTABLE 16 DY036 COOLING CAPACITIES 3 TON TABLE 17 DY048 COOLING CAPACITIES 4 TON Johnson Controls Unitary ProductsTABLE 18 DY060 COOLING CAPACITIES 5 TON Johnson Controls Unitary Products TABLE 21 STATIC RESISTANCES TABLE 22 ELECTRIC HEAT CFM LIMITATIONSSize VoltageJohnson Controls Unitary Products 2.Dual Element, Time Delay Type 1.Minimum Circuit Ampacity3.HACR type per NEC None None TABLE 26 ELECTRIC HEAT CORRECTION FACTORS TABLE 25 DY PHYSICAL DATATABLE 27 VOLTAGE LIMITATIONS1 TYPICAL POWER WIRING TYPICAL CONTROL WIRINGCOOLING ONLY 24 VOLT THERMOSTAT COOLING / HEATING ELECTRONIC THERMOSTATFIGURE 3 - UNIT DIMENSIONS 3 - 5 TON COOLING ONLY/ELECTRIC HEAT FRONT VIEW DETAIL “B” DETAIL “A”FIGURE 5 - UNIT WITH ECONOMIZER RAINHOOD FIGURE 7 - UNIT DIMENSIONS REAR VIEW TABLE 29 MINIMUM CLEARANCESHOLE OPENING SIZE DIAFIGURE 9 - TYPICAL APPLICATIONS 343615-YTG-B-0308Johnson Controls Unitary Products FIGURE 10 -FOURAND SIX POINT LOADING TABLE 31 CENTER OF GRAVITYTABLE 32 OPERATING WEIGHTS LBS FIGURE 11 -ROOFCURB DIMENSIONSMODEL SIZE 3 TONGENERAL GUIDE SPECIFICATIONSDESCRIPTION UNIT OPERATING CHARACTERISTICS UNIT CONTROLSGAS HEATING SECTION SINGLE OR 2 STAGE ELECTRIC HEATING SECTIONOTHER PRE-ENGINEEREDACCESSORIES AVAILABLE 343615-YTG-B-0308 Johnson Controls Unitary ProductsJohnson Controls Unitary Products 5005 York Drive 343615-YTG-B-0308Norman, OK