Manuals / ZyXEL Communications / Computer Equipment / Network Router

ZyXEL Communications 2864I user manual RXPkt - the number of received packets on this channel

Models: 2864I

1 156

Download 156 pages 28.71 Kb

Page 132

9.RXPkt - the number of received packets on this channel.

10.Error - the number of error packets on this channel.

11.CLU - (Current Line Utilization) - percentage of current bandwidth used on this channel.

12.ALU - (Average Line Utilization) - average CLU for this channel.

13.Up Time - time this channel has been connected to the current Remote Node.

14.Total Outgoing call Time - shows the total outgoing call time for both B1 and B2 channels since the system has been powered up.

15.Ethernet - shows the current status of the LAN connection on your Prestige.

16.Link - shows the current status of the LAN (Up or Down if it is 10Base-T; otherwise, if it is configured as AUI, this will show AUI).

17.TX Pkt - the number of transmitted packets to LAN.

18.RX Pkt - the number of received packets from LAN.

19.Collision - number of collisions.

20.Name - displays the system name of your Prestige. This information can be modified in Menu 1 - General Setup.

21.RAS S/W Version - refers to the version of the current RAS software.

22.ISDN F/W Version - refers to the version of the current ISDN firmware.

23.Ethernet Address - refers to the Ethernet MAC address assigned to your Prestige.

System Maintenance 119

Image 132

ZyXEL Communications 2864I user manual RXPkt - the number of received packets on this channel

Contents

ACCESSING THE INTERNET & INTRANET JiH5Prestige User’s Manual VersionZyXEL Limited Warranty Copyright 1997 by ZyXEL AcknowledgmentsFCC Part 15 Information Information for Canadian Users Page Contacting ZyXEL ∙ E-mailZyXEL Communications Corporation Contents 1 Introduction3 Installation 2 Before You Begin4 Configuring for Internet Access 5 Remote Node Configuration6 Dial-In Configuration 7 TCP/IP Configuration9 Bridging Configuration 10 Filter Configuration13 Telnet Configuration and Capabilities 14 System Maintenance15 Troubleshooting 16 ISDN Switch Types17 Index xiii Features Ease of InstallationIntroduction ISDN Basic Rate Interface BRI Built-in V.34 ModemMultiple Networking Protocol Support Standard Phone JackRADIUS Remote Authentication Dial In User Service DHCP Support Dynamic Host Configuration ProtocolFull Network Management PPP SecurityInternet Access Applications For Your PrestigeCall Control Data CompressionWhat This Manual Covers Multiprotocol LAN-to-LAN ConnectionTelecommuting Server Mobile Users with V.34 ModemsWhat This Manual Doesn’t Cover Other ResourcesAdditional Installation Requirements Packing List∙ VT100 terminal emulation ∙ 9600 Baud rate ∙ No parity, 8 Data bits, 1 Stop bit8 Introduction Before You Begin Road Map and FlowCompleting the Worksheet Figure 2-1 Installation Guide10 Before You Begin Collecting General Setup Information Ordering Your ISDN LineCollecting ISDN Phone Line Information Switch TypeGeography No of Phone #sAmerica, select your ISDN switch type. For DSS1 and 1TR6, verify this field to make sure that you have the proper firmware loaded Collecting Ethernet Setup Information IP Subnet MaskNumber of Host IDs Number of BitsIP Subnet Mask Number of Host IDsNumber of Bits Before You BeginGeneral Setup Information ISDN Setup InformationPrestige Setup and Installation Worksheet 16 Before You BeginNorth America ISDN DSS1 ISDN∙ 1st Telephone Number ∙ Analog Call check one1TR6 ISDN 18 Before You BeginEthernet Setup Information EAZ Don’t CareModem A/B Ignore AUI UTP20 Before You Begin Installation Figure 3-1 Rear Panel DiagramInstallation Connecting Your Computer and Your Prestige Connecting the RS-232 Cable to your PrestigeConnecting an ISDN Line to your Prestige A Warning On Connection CablesConnecting a Telephone/Fax to your Prestige Connecting an Ethernet Cable to your Prestige∙ UTP Connecting a Power Adapter to your Prestige Prestige Front PanelPowering On Your Prestige Figure 3-3 Power on Messages Figure 3-4 Login Screen26 Installation Navigating Through the System Management Terminal Interface System Management Terminal Interface Summary General Setup ISDN Setup 30 InstallationNorth American ISDN Figure 3-7 Menu 2 - ISDN Setup for North AmericaDSS1 & 1TR6 ISDN Figure 3-8 Menu 2 - ISDN Setup for DSS11. Switch Type - This field is fixed as DSS1 or 1TR6 34 Installation Figure 3-10 ISDN Loop-Back Test Screen Ethernet Setup General Ethernet SetupTCP/IP Ethernet Setup and DHCP Figure 3-12 Menu 3.2 - TCP/IP Ethernet Setup38 Installation Novell IPX Ethernet Setup Bridge Ethernet SetupConfiguring for Internet Access IP Addresses and the Internet Figure 4-1 Internet AccessInternet Access Configuration 42 Configuring for Internet Access5. My Login Name - Enter the login name given to you by your ISP ∙ Modem - The Prestige will place Modem data calls Single User Account translation, refer to RFC 1631, The IP Network Address Translator NAT In summaryConfiguration for Single User Account Configuring Backup ISP Accounts2. Enter Menu 11, then select the number of an unused remote node Configuring for Internet Access Remote Node Configuration Figure 5-1 Menu 11 - Remote Node SetupRemote Node Configuration Figure 5-2 Menu 11.1 - Remote Node Profile52 Remote Node Configuration ∙ PAP sends the user name and password in plain text 54 Remote Node Configuration 18. Telco Options Allocated Budget min - This field will set a budget outgoing call time for the Remote Node. The default for this field is 0 for no budget control Bandwidth on Demand 56 Remote Node ConfigurationEditing PPP Options ∙ 128 - Two channels will be used when a packet triggers a call to confirm your selections, or press ESC to cancel your selections58 Remote Node Configuration ∙ 64 - Only one channel will be usedDial-In Configuration Dial-In ConfigurationTelecommuting Dial-In Server ApplicationFigure 6-1 Example of Remote User Telecommuter Default Dial-In Setup Figure 6-2 Example of a Dial-In Server Application∙ None - No CLID is required 3. PPP Options Mutual Authen. - Some vendors, e.g. Cisco, implement a type of mutual authentication. That is, the node that initiates the call will request a user name and password from the far end that they are dialing to. If the Remote Node that is dialing in implements this type of authentication, set this field to Yes 11. IP Pool IP Start Addr - This field is active only if you Dial-In Users Setup Figure 6-4 Menu 14 - Dial-in User Setup 66 Dial-In ConfigurationFigure 6-5 Menu 14.1 - Edit Dial-in User 3. Password - Enter the password for the Remote Dial-in User More on CLID TCP/IP Configuration IP Subnet MaskLAN-to-LAN Application 70 TCP/IP ConfigurationRemote Node Setup 5. Rem IP Subnet Mask - Enter the subnet mask for the remote network Static Route Setup 74 TCP/IP Configuration Figure 7-4 Static Routing ExampleFigure 7-5 Menu 12 - Static Route Setup - Main Menu Figure 7-6 IP Static Route Setup76 TCP/IP Configuration Novell IPX Configuration IPX Network EnvironmentFrame Type Network NumbersPrestige on LAN with Server Prestige on LAN without ServerFigure 8-1 Prestige Operating in IPX Environment IPX Ethernet Setup IPX Spoofing∙ ∙ ∙ Ethernet ∙ SNAP Remote Node Setup LAN-to-LAN ApplicationFigure 8-3 LAN-to-LAN application configure the default dial-in parameters in menu 13 see Chapter Static Route Setup 84 Novell IPX Configuration Figure 8-5 NetWare Servers on Both Sides of the LinkFigure 8-6 Menu 12.2 - Edit IPX Static Route 86 Novell IPX Configuration Bridging Configuration Bridging ConfigurationIPX Spoofing Bridge Ethernet Setup Figure 9-1 Bridge Ethernet Setup LAN-to-LAN ApplicationRemote Node Setup 1. Bridge - Make sure this field is set to YesDefault Dial-In Setup for Bridge Bridge Static Route SetupFigure 9-3 Menu 12.4 - Bridge Static Route 92 Bridging Configuration Filter Configuration About FilteringConfiguring a Filter Set Prestige’s Filter Structure94 Filter Configuration ∙ # - Refers to the filter rule number ∙ Pr - Protocol ∙ SA - Source Address ∙ SP - Source Port number Configuring a Filter Rule TCP/IP Filter Rule∙ Yes ∙ No ∙ None ∙ Less ∙ Greater ∙ Equal ∙ Not Equal 100 Filter Configuration Generic Filter Rule Figure 10-5 Menu 21.1.1 - Generic Filter RuleNovell IPX Filter Rule 102 Filter Configuration∙ None ∙ RIP Request 104 Filter Configuration ∙ RIP Response ∙ SAP Request ∙ SAP Response∙ SAP Get Nearest Server Request ∙ SAP Get Nearest Server Response Configuring Your Prestige For SNMP Support SNMPAbout SNMP Figure 11-1 Menu 22 - SNMP Configuration 106 SNMP6. Trap Community - In this field, enter the community name that is sent with each trap to the SNMP manager. This should be treated like a password and match what the SNMP manager is expecting. The default is public 108 SNMP Using RADIUS Authentication Installing a RADIUS ServerSystem Security Configuring the Prestige for RADIUS Authentication This will bring you to Menu 23.2 - System Security - External Server Using RADIUS Authentication for CLID Adding Users to the RADIUS DatabaseConfiguring the SMT Password 114 System Security Telnet Configuration and Capabilities About Telnet ConfigurationSingle Administrator System TimeoutTelnet Capabilities System Maintenance System Status2. From this menu, select option 1. System Status 9. RXPkt - the number of received packets on this channel Terminal Baud Rate Figure 14-3 LAN Packet Which Triggered Last CallView Error Log Log and TraceSyslog And Accounting Diagnostic 124 System Maintenance Below is an example of a failed Trace Display for a Successful IPCP Connection via Manual Call Backup Configuration Restore Configuration126 System Maintenance Software Update Figure 14-9 Example of uploading RAS using PCPLUSCommand Interpreter Mode Call Control128 System Maintenance Call Control Parameters Figure 14-10 Menu 24.9.1 Call Control ParametersBlacklist Budget ManagementFigure 14-11 Blacklist Figure 14-12 Budget ManagementModem/ISDN TA Emulation 132 System Maintenance Troubleshooting Problems Starting Up the PrestigeNone of the LEDs are on when you power up the Prestige Connecting the RS-232 cable, cannot access the SMTProblems With the ISDN Line The ISDN initialization failedThe ISDN loopback test failed Problems with the LAN Interface Problems Connecting to a Remote Node or ISPCan’t PING any station on the LAN Problems Connecting to a Remote User 136 TroubleshootingISDN Switch Types Provisioning For U.S. SwitchesProvisioning For the AT&T 5ESS Switches Provisioning Feature SettingProvisioning Feature SettingProvisioning For the Northern Telecom Switch Provisioning FeatureSetting Provisioning FeatureProvisioning Feature Setting140 ISDN Switch Types EKTSIndex See IPX See POTSIP Subnet Mask, 15, 39 SPID, 11, 13, 14, 30