Manuals / Brands / Computer Equipment / Network Card / ZyXEL Communications / Computer Equipment / Network Card

ZyXEL Communications 794M 4.2.2 Change Connection Type, Next, Change, Quick Start, Quick Start

1 119

Download 119 pages, 5.18 Mb

53

Prestige 794M User’s Guide

Table 23 WAN: Edit: Advanced PPP Options (continued)

LABEL	DESCRIPTION

Give DNS to	Enable this feature to set the Prestige to provide DNS server information to a
DHCP Server.	DHCP server.
Discover Primary/	Enable this feature to set the Prestige to request NBNS (NetBIOS Name Server)
Secondary NBNS.	server information from the remote PPP peer device.
	An NBNS server (also known as a WINS server) maps a NetBIOS name to an IP
	address.
Discover Subnet	Enable this feature to set the Prestige to use the subnet mask obtained after the
Mask	Internet connection is established.
Give Subnet Mask	Enable this feature to set the Prestige to provide the subnet mask information to
to DHCP Server	the DHCP server. The subnet mask is obtained during the connection negotiation.
Apply	Click Apply to save the changes.

Reset	Click Reset to start configuring this screen again.

4.2.2 Change Connection Type

Follow the steps below to change your Internet connection type and settings.

1Click Change in the main ISP screen (see Figure 29 on page 49).

2A screen displays as shown. Select the connection type your ISP uses and click Next. Click Quick Start to configure the line settings in the Quick Start screen (refer to Section 2.7.4 on page 33 for more information).

Figure 32 ISP: Change Connection Type

3A configuration screen displays. This screen varies depending on the connection type you select. Refer to Section 4.2 on page 49 for more information.

53	Chapter 4 WAN

Contents

User’s Guide Copyright Disclaimer Trademarks Federal Communications Commission (FCC) Interference Statement Notice Certifications Safety Warnings ZyXEL Limited Warranty Note Safety Warnings Customer Support Page Table of Contents Page Page QoS (Quality of Service) Static Route Page Page List of Figures Page List of Tables Page Preface About This User's Guide Related Documentation User Guide Feedback Syntax Conventions Graphics Icons Key Introduction 1.1 About Your Prestige 1.2 Features Multi-ModeStandard 10/100M Auto-negotiatingEthernet/Fast Ethernet Interface(s) Multiplexing Full Network Management Universal Plug and Play (UPnP) Network Address Translation (NAT) Firewall 1.3 Applications 1.3.1 Internet Access 1.3.2 Firewall for Secure Broadband Internet Access 1.3.3 VPN Application 1.3.4 LAN-to-LANApplication 1.4 Hardware Connection 1.4.1 Front Panel 1.5 Rear Panel The Web Configurator 2.1 Overview 2.2Accessing the Web Configurator 2.3 Resetting the Prestige 2.3.1 Procedure To Use The Reset Button 2.4Navigating the Web Configurator 2.4.1 The Status Screen 2.5System Status 2.6 ARP Table 2.6.1 How ARP Works 2.7 Routing Table 2.7.1 PPTP Status 2.7.2 IPSec Status 2.7.3 L2TP Status 2.7.4 Email Status 2.7.5 Event Log 2.7.6 Error Log 2.7.7 NAT Sessions 2.8 Internet Access Quick Start Setup Page 2.8.1 Auto Scan LAN 3.1 Overview 3.2 LAN TCP/IP 3.2.1 Factory LAN Defaults 3.2.2 IP Address and Subnet Mask 3.3The Ethernet Screen 3.4 Ethernet Client Filter 3.4.1 Ethernet Client Filter Candidates 3.5 Port Setting 3.6 DHCP 3.6.1 IP Pool Setup 3.6.2 DNS Servers 3.6.3DHCP Setup 3.6.3.1 Disable DHCP 3.6.3.2 DHCP Server Setup Page 3.6.4 DHCP Relay Agent DHCP Relay WAN 4.1 Overview 4.1.1 Encapsulation Types 4.1.1.1 RFC 4.1.1.2 PPPoE 4.2 ISP 4.2.1 Edit Settings 4.2.1.1 Advanced PPP Options Page 4.2.2 Change Connection Type 4.3DNS 4.4 SHDSL Parameters Table 25 SHDSL Page System 5.1 Overview 5.2 Time Zone 5.3 Remote Access 5.4 Firmware Upgrade 5.5Backup/Restore 5.6 Restart Router 5.7 User Management 5.7.1 Create a New User Account Page Firewall 6.1 Overview 6.2 Types of Firewalls 6.2.1Packet Filtering Firewalls 6.2.2 Application-levelFirewalls 6.2.3Stateful Inspection Firewalls 6.3 General Settings 6.4 Packet Filter Policy Firewall: General Settings 6.4.1 Add a New TCP/UDP Packet Filter 6.4.2 Add a New Raw Packet Filter 6.5 Intrusion Detection Intrusion Detection 6.6 URL Filter 6.6.1 Keywords Filtering 6.6.2 Domain Filtering 6.7 Firewall Log Page VPN 7.1 Overview 7.2 PPTP 7.2.1 PPTP Summary 7.2.2 Creating a PPTP VPN Rule 7.2.2.1 Remote Access Connection Page 7.2.2.2 LAN to LAN Connection Page 7.3 IPSec 7.3.1 AH (Authentication Header) 7.3.2 ESP (Encapsulating Security Payload) 7.3.3 Perfect Forward Secrecy (PFS) 7.3.4 Pre-SharedKey 7.3.5 IPSec VPN Summary 7.3.6 IPSec VPN Configuration Page 7.4 L2TP 7.4.1 Creating a New L2TP Rule 7.4.1.1 Remote Access L2TP Connection Page 7.4.1.2 LAN to LAN L2TP Connection Page Page 7.5 VPN Example 7.5.1 Example: Remote PPTP VPN Dial-inConnection 7.5.2 Example: Remote PPTP VPN Dial-outConnection MUST QoS (Quality of Service) 8.1 Overview 8.1.1 Prioritization Page 8.2 IP Throttling Page 8.3 QoS Example 8.3.1 Example Prioritization with QoS 8.3.2 Rate Limiting with IP Throttling Example 8.4 Time Schedule 8.4.1 Configuring a Time Schedule Page Static Route 9.1 Overview 9.2 Configuration Page Dynamic DNS 10.1 Overview 10.1.1 Configuration Page Check Emails 11.1 Overview 11.2 Configuring Page Device Management 12.1 Overview 12.1.1 Universal Plug and Play (UPnP) 12.1.1.1 How do I know if I'm using UPnP 12.1.1.2 Cautions with UPnP 12.1.2.1SNMPv3 12.1.2.2 SNMP Traps and MIBs 12.2 The Device Management Screen WAN Page 12.3 IGMP Numerics Index