Husqvarna 240e, 235e manuel dutilisation Maintenance schedule, Daily maintenance Every 5-10 h

Page 21

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

Daily maintenance (Every 5-10 h)

Weekly maintenance (Every 10-25 h)

Monthly maintenance (Every 25-40 h)

 

 

 

 

 

Check the brake band on the chain

Clean the outside of the machine.

Check the starter, the starter cord and

brake for wear. Replace when less than

the recoil spring.

0.024 inch (0.6 mm) remains at the most

 

 

 

worn point.

 

 

 

Check that the components of the

Check that the vibration damping

Check the clutch centre, clutch drum

throttle control work safely. (Throttle

elements are not damaged.

and clutch spring for wear.

lockout and throttle control.)

 

 

 

 

 

Clean the chain brake and check that

 

 

it operates safely. Make sure that the

File off any burrs from the edges of the

Clean the spark plug. Check that the

chain catcher is undamaged, and

bar.

electrode gap is 0.020 inch (0.5 mm).

replace it if necessary.

 

 

 

 

 

The bar should be turned daily for

 

 

more even wear. Check the lubrication

 

 

hole in the bar, to be sure it is not

Clean the carburetor compartment.

Clean the outside of the carburetor.

clogged. Clean the bar groove. If the

 

 

bar has a sprocket tip, this should be

 

 

lubricated.

 

 

 

 

 

Check that the bar and chain are

Clean the air filter. Replace if

Check fuel hose for cracks or other

getting sufficient oil.

necessary.

damage. Change if necessary.

 

 

 

Check the saw chain with regard to

 

 

visible cracks in the rivets and links,

 

 

whether the saw chain is stiff or

 

Empty the fuel tank and clean the inside.

whether the rivets and links are

 

 

 

abnormally worn. Replace if

 

 

necessary.

 

 

 

 

 

Sharpen the chain and check its

 

 

tension and condition. Check the drive

 

Empty the oil tank and clean the inside.

sprocket for excessive wear and

 

 

 

replace if necessary.

 

 

 

 

 

Clean the starter units air intake.

 

Check all cables and connections.

 

 

 

Check that nuts and screws are tight.

 

 

 

 

 

Check that the stop switch works

 

 

correctly.

 

 

 

 

 

Check that there are no fuel leaks from

 

 

the engine, tank or fuel lines.

 

 

 

 

 

5451676-63 Rev.1 2008-04-14

English – 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 235e 240e 5451676-63 Rev.1 OFF Half Full 49 a Retreat path Thank you for using a Husqvarna product Symbols on the machineIntroduction Dear customerWhat is what on the chain saw? Contents General Safety Precautions Before using a new chain sawFor Canada Always use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardCutting equipment General rules Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback BarLubricating cutting equipment Tensioning the chainHappen when the chain touches the operator General Safety Precautions / AssemblyFitting the bar and chain Chain drive sprocketFuel Handling Fuel safetyFuel FuelingStarting and stopping Fuel Handling / Starting and StoppingWorking Techniques Basic safety rulesBefore use General working instructionsTree felling technique Basic cutting techniqueFreeing a tree that has fallen badly How to avoid kickback Working Techniques / MaintenanceCarburetor adjustment GeneralMuffler MaintenanceAir filter Spark plugDaily maintenance Every 5-10 h Maintenance scheduleTechnical data Technical DataBar Chain Recommended cutting equipment for CanadaYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsSymboles sur la machine Cher clientNous vous remercions dutiliser un produit Husqvarna Sommaire Quels sont les composants de la tronçonneuse?Mesures à prendre avant de mettre en usage une Consignes de sécurité pour les utilisateurs deInstructions Générales DE Sécurité Équipement de sécurité de la machine Utilisez toujours votre bon sensFrein de chaîne avec arceau protecteur AVERTISSEMENT! La plupart desCapteur de chaîne Blocage de l’accélérationProtection de la main droite Système anti-vibrationsRègles élémentaires Équipement de coupeÉquipement de coupe anti-rebond Affûtage et réglage de l’épaisseur du copeau de la chaîneLubrification de l’équipement de coupe Tension de la chaîneMontage du guide-chaîne et de la chaîne Instructions Générales DE Sécurité / MontageManipulation DU Carburant CarburantRemplissage de carburant Transport et rangement Sécurité carburantRemisage prolongé AVERTISSEMENT! N’utilisez jamais uneDémarrage et arrêt Démarrage ET ArrêtAvant chaque utilisation Techniques DE TravailMéthodes de travail Règles élémentaires de sécuritéGénéralités Technique de base pour la coupeToujours travailler à plein régime TerminologieTechniques d’abattage Solution à un abattage ratéQu’est-ce qu’un rebond? Mesures anti-rebondGénéralités EntretienRéglage du carburateur FonctionnementSilencieux Filtre à airBougie Schéma d’entretien Caractéristiques techniques Caractéristiques TechniquesType Guide-chaîne ChaîneVOS Droits ET Obligations EN Garantie Autres consignes de sécurité Précautions à prendre pour se protéger des rebondsAnsi B 175.1-2000 Annexe C AVERTISSEMENT! N’utilisez pas uneIntroduccion Apreciado clienteSímbolos en la máquina ¿Qué es qué en la motosierra? Índice Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Emplee siempre el sentido comúnEquipo de seguridad de la máquina Equipo de protección personalFreno de cadena con protección contra reculadas ¡ATENCION! La mayoría de losCaptor de cadena Fiador del aceleradorProtección de la mano derecha Sistema amortiguador de vibracionesEquipo de corte Reglas básicasEquipo de corte reductor de reculadas Lubricación del equipo de corte Tensado de la cadenaCerrar la manija para fijar el tensado Repostaje de aceite para cadena de motosierraMontaje de la espada y la cadena Instrucciones Generales DE Seguridad / MontajeCarburante Manipulacion DEL CombustibleRepostaje Seguridad en el uso del combustibleArranque y parada Manipulacion DEL Combustible / Arrenque Y ParadaAntes de utilizar la máquina Tecnica DE TrabajoReglas básicas de seguridad Corte con velocidad de cadena alta, acelerando al máxTécnica de tala Técnica básica de corteTratamiento de una tala fallida Mantenimiento GeneralidadesAjuste del carburador Silenciador Filtro de aireBujía Programa de mantenimiento Datos técnicos Datos TecnicosEspada Cadena SUS Derechos Y Obligaciones DE Garantia Precauciones de seguridad en reculadas Precauciones de seguridad para usuarios de motosierrasOtras precauciones de seguridad Ansi B 175.1-2000 Anexo C5451676-63 2008-04-15
Related manuals
Manual 26 pages 62.88 Kb

240e, 235e specifications

The Husqvarna 235E and 240E are two popular models in the world of lightweight chain saws, designed to deliver excellent performance for both novice and experienced users. Ideal for homeowners and professionals alike, these models are perfect for tasks such as cutting firewood, pruning, and handling small trees.

One of the standout features of the Husqvarna 235E and 240E is their lightweight construction. Weighing in at around 10.3 pounds, these chainsaws are easy to maneuver, reducing fatigue during extended use. The ergonomic design enhances comfort, making it easier for users to maintain a firm grip, especially during challenging cutting tasks.

These models are equipped with the powerful X-Torq engine technology, which provides a significant increase in efficiency. The X-Torq engine reduces fuel consumption by up to 20%, allowing users to work longer without the need for frequent refueling. Additionally, the engine's design minimizes harmful emissions, making the 235E and 240E more environmentally friendly.

Another important characteristic is the chainsaw’s emissions control system. Husqvarna has integrated an efficient air filtration system in both models, ensuring that dirt and debris are kept away from the engine for extended periods. This results in less maintenance and longer operational life.

Ease of starting is also a highlight of these models. The Smart Start technology ensures that the chainsaw can be started with minimal effort, allowing users to get to work quickly. The combined choke and stop control further simplify the starting process, ensuring a smooth operation every time.

Safety features are not overlooked in the Husqvarna 235E and 240E. Each model comes with a chain brake that responds quickly to stop the chain in case of kickback, which is essential for preventing accidents during operation. The low-vibration design reduces strain on the hands and arms, fostering a safer and more comfortable user experience.

Overall, the Husqvarna 235E and 240E offer a combination of power, efficiency, and user-friendly features that set them apart in their category. With a focus on performance and safety, these chainsaws are an excellent choice for anyone looking to tackle cutting, trimming, and pruning tasks with ease and confidence. Whether you are a homeowner looking to manage your yard or a professional seeking reliable equipment, the 235E and 240E are worthy contenders.
Top Page Image Contents