Husqvarna 535RXT manual Cutting equipment, Locking nut

Page 10

GENERAL SAFETY PRECAUTIONS

WARNING! Mufflers fitted with catalytic

! converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin.

Remember the risk of fire!

WARNING! The inside of the muffler

! contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING! Bear in mind that:

! The exhaust fumes from the engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!

Locking nut

A locking nut is used to secure some types of cutting attachment.

When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.) Tighten the nut using the socket spanner.

The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of blade thrust.

•Obtain maximum cutting performance.

•Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.

Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.

Maintain the correct blade setting! Follow our instructions and use the recommended file gauge.

WARNING! Always stop the engine

! before doing any work on the cutting attachment.This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

WARNING! Using an incorrect cutting

! attachment or an incorrectly sharpened blade increases the risk of blade thrust.

Cutting equipment

Saw blades are intended for cutting fibrous types of wood.

Grass blades and grass cutters are intended for cutting coarse grass.

A trimmer head is intended for trimming grass.

10 – English

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 535RX, 535RXT KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what on the brush cutter?General Safety Precautions Personal protective equipment Machine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard 535RX, 535RXTQuick release MufflerLocking nut Cutting equipmentCutting equipment Sharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Fitting the guard extension AssemblySee the chapter on Technical data. If an Attachment without an approved guardFitting a blade guard, grass blade and grass cutter Fitting the blade guard and saw bladeFitting other guards and cutting attachments Standard harness Adjusting the harness and brush cutterTriobalance harness Correct balance Fuel Handling Fuel safetyFuel Muffler gets very hot during and after FuelingMixing Use. This also applies during idling. BeStarting and stopping Starting and StoppingCheck before starting StartingFor throttle handles with a start throttle lock StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingIs running or the cutting equipment is Up into the eyes causing blindness orAreas where it is difficult to see Rotating, as this can result in seriousForestry clearing using a saw blade Brush cutting with a saw bladeTrimming Grass clearing using a grass bladeGrass trimming with a trimmer head ClearingCutting SweepingMaintenance CarburetorCooling system MufflerBevel gear Spark plug Cleaning the air filterAir filter Oiling the air filterMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Emission Warranty Parts List Page S35 2,7mm 095-.106 25 m 15 cm T35, T35x T45, T45x Auto Trimmy SII Page Page Original instructions 1154017-95
Top Page Image Contents