Husqvarna Essential Maintenance Tips for Brush Cutters

Page 29

MAINTENANCE

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts

Excessive fuel consumption.

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refitting it.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter

must always be replaced.

If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter.

Oiling the air filter

Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never

use common engine oil. This would drain through the filter quite quickly and collect in the bottom.

Spark plug

The spark plug condition is influenced by:

Incorrect carburetor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/ cylinder.

Note: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA.

English 29

Image 29
Contents 535RX, 535RXT Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the brush cutter? What is WHAT?Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentCutting attachment guard Stop switchVibration damping system 535RX, 535RXTMuffler Quick releaseCutting equipment Cutting equipmentLocking nut Sharpening the saw blade Sharpening grass cutters and grass bladesTrimmer head See the chapter on Technical data. If an AssemblyFitting the guard extension Attachment without an approved guardFitting the blade guard and saw blade Fitting a blade guard, grass blade and grass cutterFitting other guards and cutting attachments Triobalance harness Adjusting the harness and brush cutterStandard harness Correct balance Fuel Fuel safetyFuel Handling Mixing FuelingMuffler gets very hot during and after Use. This also applies during idling. BeCheck before starting Starting and StoppingStarting and stopping StartingStopping For throttle handles with a start throttle lockWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingAreas where it is difficult to see Up into the eyes causing blindness orIs running or the cutting equipment is Rotating, as this can result in seriousBrush cutting with a saw blade Forestry clearing using a saw bladeGrass trimming with a trimmer head Grass clearing using a grass bladeTrimming Clearing Sweeping CuttingCarburetor MaintenanceBevel gear MufflerCooling system Air filter Cleaning the air filterSpark plug Oiling the air filterMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Emission Warranty Parts List Page S35 2,7mm 095-.106 25 m 15 cm T35, T35x T45, T45x Auto Trimmy SII Page Page Original instructions 1154017-95