Ryobi Outdoor CS30, SS30, BC30 manual Attaching the Shoulder Harness BC30, See Figures 10

Page 13

ASSEMBLY

ATTACHING THE SHOULDER HARNESS - BC30

See Figure 9.

1.Connect the latch on the shoulder harness to the strap hanger.

2.Adjust the strap to a comfortable position.

CONVERTING FROM BRUSHCUTTER TO STRING TRIMMER - BC30

To convert from the brushcutter to the string trimmer, remove the blade and brushcutter guard, attach the straight shaft grass deflector and install the string head.

REMOVING THE TRI-ARC® BLADE AND

BRUSHCUTTER GUARD

See Figures 10 -11.

1.Align the slot in the flanged washer with the slot in the gear head.

2.Place the gear head locking tool through the slot in the flanged washer and gear head.

3.Remove the blade nut by turning it clockwise.

4.Remove the cupped washer and the blade

5.Remove the flanged washer from the gear head shaft and retain it for the string head installation.

6.Remove the three screws securing the brushcutter guard to gear head.

7.Remove the brushcutter guard.

NOTE: Store the brushcutter parts together for later use.

INSTALLING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD

See Figures 10 - 12.

1.Install the grass deflector. Refer to “To Attach the Straight Shaft Grass Deflector” earlier in this manual.

2.Place the flanged washer on the gear head shaft.

NOTE: The hollow side of the flanged washer should face the gear head.

3. Align the slot in the flanged washer with the slot in the gear head.

4. Place the gear head locking tool through the slot in the flanged washer and gear head.

5. Install the string head assembly onto the gear head shaft by turning counterclockwise.

6. Tighten the string head assembly securely.

LATCH

STRAP HANGER

 

SHOULDER

 

HARNESS

Fig. 9

 

GEAR HEAD

LOCKING TOOL

Fig. 10

GEAR HEAD

BRUSHCUTTER

GUARD

FLANGED

WASHER

SLOT

CUPPED

WASHER

BLADE NUT

Fig. 11

GEAR HEAD

FLANGED WASHER

STRING HEAD

ASSEMBLY

SLOT

LOOSEN

TIGHTEN

Fig. 12

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operators Manual Introduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSHCUT- TER and Blade USE Symbol Name Explanation SymbolsSymbol Signal Meaning ServiceUnpacking SpecificationsCS30 RY30020, RY30023 FeaturesSS30 RY30040, RY30043 Attaching the Power Head to the Attachment AssemblyRemoving the Attachment from the Power Head Attaching the Storage HangerAttaching the J Barrier Handle BC30 Attaching the Front Handle CS30 and SS30Attaching the Brushcutter Guard BC30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 To Attach the Straight Shaft Grass Deflector SS30Converting from Brushcutter to String Trimmer BC30 Attaching the Shoulder Harness BC30Removing the TRI-ARC Blade Brushcutter Guard See Figures 10Converting from String Trimmer to Brushcutter BC30 Installing the TRI-ARC Blade Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Fueling and Refueling the Trimmer OperationOperating the Trimmer To Advance the Cutting Line Manually To Advance the Cutting LineCutting Tips See Figures 16Blade Thrust Operating the BrushcutterTRI-ARC Blade Cutting Technique BladeSee Figures 21 Starting and StoppingTo Start a Cold Engine To Stop the EngineSpool Replacement MaintenanceNEW Prewound Spool See Figures 24See Figures 26 String ReplacementReplacing and Cleaning AIR Filter Cleaning the Exhaust Port and Muffler Spark ArrestorSee Figures 29 Spark Plug Fuel CAPStorage 1 Month or Longer Problem Possible Cause Solution TroubleshootingCall Manufacturers Warranty Coverage WarrantyPage Emissions Maintenance Schedule and Warranted Parts List Service
Top Page Image Contents