Ryobi Outdoor CS30, SS30, BC30 manual Specific Safety Rules for Trimmer USE

Page 4

SPECIFIC SAFETY RULES

SPECIFIC SAFETY RULES FOR TRIMMER USE

nReplace string head if cracked, chipped, or damaged in any way. Be sure the string head or blade is properly installed and securely fastened. Failure to do so can cause serious injury.

nMake sure all guards, straps, deflectors and handles are properly and securely attached.

nUse only the manufacturer's replacement string in the cutting head. Do not use any other cutting attachment. To install any other brand of cutting head to this string trimmer can result in serious personal injury.

nNever operate unit without the grass deflector in place and in good condition.

nMaintain a firm grip on both handles while trimming. Keep string head below waist level. Never cut with the string head located over 76 cm (30 in.) or more above the ground.

SPECIFIC SAFETY RULES FOR BRUSHCUT- TER AND BLADE USE

nAfter engine stops, keep rotating blade in thicker weeds or pulpy stalks until it stops.

nDo not operate the brushcutter unless the brushcutter guard is firmly secured in place and in good condition.

nUse heavy gloves when operating the brushcutter and when installing or removing blades.

nAlways stop the engine and remove the spark plug wire before attempting to remove any obstruction caught or jammed in the blade or before removing and installing the blade.

nDo not attempt to touch or stop the blade when it is rotating.

nA coasting blade can cause injury while it continues to spin after the engine is stopped or throttle trigger released. Maintain proper control until the blade has completely stopped rotating.

nReplace any blade that has been damaged. Always make sure blade is installed correctly and securely fastened before each use. Failure to do so can cause serious injury.

nUse only the manufacturer's replacement Tri-Arc® blade intended for use on this brushcutter. Do not use any other blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury.

nThe Tri-Arc® blade is suited for cutting thicker weeds or pulpy stalks only. Do not use for any other purpose. Never use the Tri-Arc® blade to cut woody brush.

nExercise extreme caution when using the blade with this unit. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the op- erator to lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut from the right to the left. In the event an unexpected object or woody stock is encountered, this could minimize the blade thrust reaction.

nNever cut any material over 13 mm (1/2 in.) diameter.

nAlways wear the shoulder harness when using the brush- cutter and adjust to a comfortable operating position. Main- tain a firm grip on both handles while cutting with a blade. Keep the blade away from body and below waist level.

nNever use the brushcutter with the blade located 76 cm (30 in.) or more above the ground level.

Page 4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operators Manual Table of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSHCUT- TER and Blade USE Symbols Symbol Name ExplanationService Symbol Signal MeaningSpecifications UnpackingFeatures CS30 RY30020, RY30023SS30 RY30040, RY30043 Assembly Attaching the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerAttaching the Front Handle CS30 and SS30 Attaching the J Barrier Handle BC30Attaching the Grass Deflector Attaching the Brushcutter Guard BC30To Attach the Curved Shaft Grass Deflector CS30 To Attach the Straight Shaft Grass Deflector SS30Attaching the Shoulder Harness BC30 Converting from Brushcutter to String Trimmer BC30Removing the TRI-ARC Blade Brushcutter Guard See Figures 10Converting from String Trimmer to Brushcutter BC30 Installing the TRI-ARC Blade Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Fueling and Refueling the Trimmer OperationOperating the Trimmer To Advance the Cutting Line To Advance the Cutting Line ManuallyCutting Tips See Figures 16Operating the Brushcutter Blade ThrustTRI-ARC Blade Cutting Technique BladeStarting and Stopping See Figures 21To Start a Cold Engine To Stop the EngineMaintenance Spool ReplacementNEW Prewound Spool See Figures 24String Replacement See Figures 26Replacing and Cleaning AIR Filter Cleaning the Exhaust Port and Muffler Spark ArrestorSee Figures 29 Spark Plug Fuel CAPStorage 1 Month or Longer Troubleshooting Problem Possible Cause SolutionCall Warranty Manufacturers Warranty CoveragePage Emissions Maintenance Schedule and Warranted Parts List Service
Top Page Image Contents