Ryobi Outdoor CS30, SS30, BC30 manual String Replacement, See Figures 26

Page 20

MAINTENANCE

STRING REPLACEMENT

See Figures 26 - 28.

Use only monofilament string. Use original manufacturer's replacement string for best performance.

String Diameter:

CS30 - .080 in. (2.0 mm)

SS30 - .095 in. (2.4 mm)

BC30 - .095 in. (2.4 mm)

1.Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for models CS30.

Turn the spool retainer clockwise for models SS30 and BC30.

2.Remove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool.

3.Cut two pieces of string, each being approximately 9 ft. (2.7 m) long.

4.Insert the first string into the anchor hole in the upper part of the spool. Wind the first string around the upper part of the spool counterclockwise, as shown by the arrows on the spool. Place string in the slot on upper spool flange, leaving about 6 in. (152 mm) extended beyond the slot. Do not overfill. After winding the string, there should be at least 1/4 in. (6 mm) between the wound string and the outside edge of the spool.

5.Repeat above step with second string, using the bottom part of spool. Do not overfill.

6.Replace the spool and the spool retainer. Refer to “Spool Replacement” earlier in this manual.

SPRING

FIRST STRING

FIRST STRING

SLOT

SLOT

SPOOL

ARROWS ON

SPOOL

ANCHOR HOLE

Fig. 26

SECOND

STRING

Fig. 27

ARROWS ON

SPOOL

Fig. 28

Page 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operators Manual Table of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for BRUSHCUT- TER and Blade USE Specific Safety RulesSpecific Safety Rules for Trimmer USE Symbols Symbol Name ExplanationService Symbol Signal MeaningSpecifications UnpackingFeatures CS30 RY30020, RY30023SS30 RY30040, RY30043 Assembly Attaching the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerAttaching the Front Handle CS30 and SS30 Attaching the J Barrier Handle BC30Attaching the Grass Deflector Attaching the Brushcutter Guard BC30To Attach the Curved Shaft Grass Deflector CS30 To Attach the Straight Shaft Grass Deflector SS30Attaching the Shoulder Harness BC30 Converting from Brushcutter to String Trimmer BC30Removing the TRI-ARC Blade Brushcutter Guard See Figures 10Removing the Straight Shaft Grass Deflector and String Head Installing the TRI-ARC Blade Brushcutter GuardConverting from String Trimmer to Brushcutter BC30 Operating the Trimmer OperationFueling and Refueling the Trimmer To Advance the Cutting Line To Advance the Cutting Line ManuallyCutting Tips See Figures 16Operating the Brushcutter Blade ThrustTRI-ARC Blade Cutting Technique BladeStarting and Stopping See Figures 21To Start a Cold Engine To Stop the EngineMaintenance Spool ReplacementNEW Prewound Spool See Figures 24String Replacement See Figures 26See Figures 29 Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Storage 1 Month or Longer Fuel CAPSpark Plug Troubleshooting Problem Possible Cause SolutionCall Warranty Manufacturers Warranty CoveragePage Emissions Maintenance Schedule and Warranted Parts List Service
Top Page Image Contents