Ryobi Outdoor CS30, SS30, BC30 manual Attaching the Front Handle CS30 and SS30

Page 11

ASSEMBLY

ATTACHING THE FRONT HANDLE - CS30 AND SS30

See Figure 4.

1.Remove the front handle, bolt, flat washer, lock washer, and wing nut from the Owner’s Kit.

2.Install the front handle onto the top side of the drive shaft housing and move it to a comfortable position.

3.Place the bolt through the front handle

NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle.

4.Install the flat washer, lock washer, and wing nut.

5.Tighten wing nut securely.

ATTACHING THE “J” BARRIER HANDLE - BC30

See Figure 5.

A barrier handle must be used for ensuring the best control and maximizing operator safety when using a brushcutter.

1.Hold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator's left.

2.Insert the end of the handle between the clamps.

3.Align the bolt holes and push the long bolt (1/4-20 x 1-1/2 in.) through the handle side.

4.Place short bolt (1/4-20 x 1 in.) through opposite side of clamp. Install flat washer, lock washers and hex nuts to hold the assembly in place.

5.After assembly is complete, adjust the position of the handle for best balance and comfort.

6.Tighten first the long bolt and then the short bolt.

FRONT HANDLE

LOCK

 

 

WASHER

WING

NUT

BOLT

FLAT WASHER

Fig. 4

 

BOLT

 

FRONT

1/4-20 x 1 in.

BOLT

 

 

1/4-20 x 1 1/2 in.

HANDLE

 

 

 

STRAP

HANGER

CLAMP

CLAMP

FLAT WASHER

 

LOCK WASHER

HEX NUT

Fig. 5

Page 11

Image 11
Contents Operators Manual Introduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for BRUSHCUT- TER and Blade USE Specific Safety RulesSpecific Safety Rules for Trimmer USE Symbol Name Explanation SymbolsSymbol Signal Meaning ServiceUnpacking SpecificationsCS30 RY30020, RY30023 FeaturesSS30 RY30040, RY30043 Attaching the Storage Hanger AssemblyAttaching the Power Head to the Attachment Removing the Attachment from the Power HeadAttaching the J Barrier Handle BC30 Attaching the Front Handle CS30 and SS30To Attach the Straight Shaft Grass Deflector SS30 Attaching the Grass DeflectorAttaching the Brushcutter Guard BC30 To Attach the Curved Shaft Grass Deflector CS30See Figures 10 Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Removing the TRI-ARC Blade Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Installing the TRI-ARC Blade Brushcutter GuardConverting from String Trimmer to Brushcutter BC30 Operating the Trimmer OperationFueling and Refueling the Trimmer See Figures 16 To Advance the Cutting LineTo Advance the Cutting Line Manually Cutting TipsCutting Technique Blade Operating the BrushcutterBlade Thrust TRI-ARC BladeTo Stop the Engine Starting and StoppingSee Figures 21 To Start a Cold EngineSee Figures 24 MaintenanceSpool Replacement NEW Prewound SpoolSee Figures 26 String ReplacementSee Figures 29 Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Storage 1 Month or Longer Fuel CAPSpark Plug Problem Possible Cause Solution TroubleshootingCall Manufacturers Warranty Coverage WarrantyPage Emissions Maintenance Schedule and Warranted Parts List Service