Poulan 183313 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Pliers

(1)

3/4" wrench

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten se- curely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

STEERING

 

WHEEL INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

 

STEERING

 

WHEEL

STEERING

 

BOOT

TABS

 

ADAPTER

EXTENSION

 

 

SHAFT

1/4 LOCKNUT

1/4 HEX BOLT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See “BATTERY” in the Customer Responsibilities sec- tion of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. PC1538B General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering WheelHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Customer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemEngine Muffler CleaningAIR Filter See Fig Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak BATTERYSee Fig To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust CarburetorEngine Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PC1538B, Product Number 954 56Electrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Wheel Steering 175131 Axle Asm Optional Equipment 170551 Control Th/ch Flag Seat LSB42 DecalsWheels & Tires LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

183313 specifications

The Poulan 183313 is a high-performance chainsaw designed for both professional and residential use. Engineered by Poulan, a brand known for its reliable outdoor power equipment, the 183313 model stands out with its powerful engine and innovative features. This chainsaw is particularly favored by tree care professionals, landscapers, and homeowners who require efficient cutting performance.

One of the main features of the Poulan 183313 is its robust engine. It is powered by a 18-inch bar and features a 42cc gas engine, which delivers ample power for a variety of cutting tasks. This powerful engine ensures that the chainsaw can efficiently handle branches, logs, and even whole trees with ease, making it perfect for tasks ranging from storm cleanup to firewood preparation.

The Poulan 183313 incorporates advanced technologies to enhance its performance and user experience. One such feature is the automatic oiling system. This system ensures that the saw chain is adequately lubricated during operation, which not only prolongs the life of the chain but also improves cutting efficiency. Additionally, the easy-start technology minimizes the effort needed to start the engine, allowing users to get to work quickly without excessive pulling.

Another characteristic of the Poulan 183313 is its lightweight design, which allows for better maneuverability and reduced user fatigue during extended use. The chainsaw also comes equipped with a wraparound handle, providing users with better grip and control during operation. This ergonomic design is especially beneficial for those who may need to work in awkward positions or for longer durations.

Safety features are also paramount in the design of the Poulan 183313. It is equipped with a chain brake that automatically stops the chain in the event of kickback, enhancing the user's safety during operation. Additionally, the front handguard adds an extra layer of protection, ensuring that users are shielded from potential hazards.

Overall, the Poulan 183313 chainsaw combines power, efficiency, and safety, making it an excellent choice for anyone looking for a reliable outdoor cutting tool. Whether you're a professional arborist or a homeowner tackling weekend projects, this chainsaw is designed to meet a variety of cutting needs with ease and confidence.
Top Page Image Contents