Poulan 968999507, 968999516 manual Maintenance, Safety Instructions

Page 13
Maintenance

SAFETY INSTRUCTIONS

Maintenance

WARNING!

The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

Use only approved gasoline container.

Never remove gas cap or add fuel with the engine running. Allow engine to cool at least two (2) minutes before refueling.

Never fuel the machine indoors.

Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliances.

Before you begin refueling, minimize the risk of static electricity by touching a metal surface.

Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from your vehicle when filling.

Remove gas-powered equipment from the truck or tailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

If fuel is spilled on clothing, change clothing immediately.

Never overfill fuel tank. Replace gas cap and tighten securely.

Do not start the engine near spilled fuel.

Never use gasoline as a cleaning agent.

If leaks arise in the fuel system, the engine must not be started until the problem has been resolved.

8011-516

Never fill the fuel tank indoors

WARNING!

The engine and the exhaust system, become very hot during operation.

Risk for burns if touched.

Allow engine and exhaust system to cool at least two (2) minutes before refueling

English-11

Image 13
Contents Pro 925 ZX Pro 950 ZX English968999516 968999507 Operator´s manualPage OPERATOR’S MANUAL RIDER Z SERIES ContentsEnglish-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSRead Safety Instructions SAFETY INSTRUCTIONSGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance •Use protective goggles IMPORTANT INFORMATION TransportCustomer responsibilities Controls CONTROLSControl Locations Tracking 1. Motion Control Levers3. Fuses 2. Seat adjustment knobs4. By pass linkages 5. Refueling 6. Blade switch8. Choke Control 7. Ignition Switch9. Throttle Control 11. Parking Brake 10. Hour Meter12. Cutting height pedal AccessoriesOperation OPERATIONTraining Starting the Engine Before Starting6.Move the throttle to the middle position IMPORTANT INFORMATION To start an engine with a weak battery Running Operating on hills Mowing patterns Mowing TipsStopping the Engine Moving by Hand Maintenance MAINTENANCEMaintenance Schedule Check/adjust throttle cable Battery Ignition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake and tighten the clamping screwReplacing the Air Filter Checking Tire Pressures Replacing the Fuel FilterChecking the Parking Brake Deck belt Checking the V-belts1. Clutch pulley Deck belt installationBelt installation EZT beltChecking the Blades Adjusting the Mower Deck To level deck Side-to-sideadjustmentFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Caster Wheels Cleaning and WashingHardware Use protective glasses when cleaning and washingLubrication LUBRICATIONLubrication Schedule Lubricating the Cables IMPORTANT INFORMATION 2. Changing the Oil Filter Checking the oil levelTransmission Trouble Shooting Guide TROUBLE SHOOTING GUIDEWrong fuel type Uneven mowing results STORAGE ServiceStorage Winter StorageWiring diagram WIRING DIAGRAMSTechnical Data TECHNICAL DATAProductivity EquipmentTorque Specifications U.S. Standard Hardware TORQUE SPECIFICATIONS HEX HEAD CAP SCREWSMetric Standard Hardware Conformity Certificates CONFORMITY CERTIFICATESUSA requirements Service Journal SERVICE JOURNALDelivery Service 1. Change engine oil After the First 5-8Hours4.Check battery with cables 25-HourService5.Check/clean the engine’s cooling air intake 6.Clean the air cleaner’s pre-filterfoam1.Perform the 25-hourservice 50-HourService5.Check/adjust the parking brake 3.Change the engine oil2.Perform the 50-hourservice 100-HourService4.Clean/replace the spark plug 3.Change the engine oil filter300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06