Poulan 968999507, 968999516 manual Safety Instructions, •Use protective goggles

Page 15
•Use protective goggles.

SAFETY INSTRUCTIONS

corrosive burns. If you spill battery acid on your skin, rinse immediately with water.

Acid in the eyes can cause blindness, contact a doctor immediately.

Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks. The battery can explode and cause serious injury/damage.

Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition.

Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.

Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.

Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery.

WARNING!

Avoid electrical sparking and its consequences by the following routines:

Use protective goggles.

Ensure that the fuel filler cap is mounted tightly and no flammable substances is stored in an open vessel.

Never work with the starter circuit if there is spilled fuel.

Disconnect the chassis cable from the battery first and reconnect it last.

Do not make a bridge short circuit across the starter relay to run the starter.

Never use the machine indoors or in spaces lacking proper ventilation. The

6003-009

Do not smoke when performing maintenance on the battery. The battery can explode and cause serious injury/damage

8009-728

Risk of sparking

English-13

Image 15
Contents Operator´s manual EnglishPro 925 ZX Pro 950 ZX 968999516 968999507Page OPERATOR’S MANUAL RIDER Z SERIES ContentsEnglish-2 General INTRODUCTIONIntroduction CongratulationsManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSRead SAFETY INSTRUCTIONS Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance •Use protective goggles IMPORTANT INFORMATION TransportCustomer responsibilities CONTROLS ControlsControl Locations Tracking 1. Motion Control Levers3. Fuses 2. Seat adjustment knobs4. By pass linkages 5. Refueling 6. Blade switch7. Ignition Switch 8. Choke Control9. Throttle Control 11. Parking Brake 10. Hour Meter12. Cutting height pedal AccessoriesOPERATION OperationTraining Starting the Engine Before Starting6.Move the throttle to the middle position IMPORTANT INFORMATION To start an engine with a weak battery Running Operating on hills Mowing patterns Mowing TipsStopping the Engine Moving by Hand MAINTENANCE MaintenanceMaintenance Schedule Check/adjust throttle cable Battery Ignition System Checking the Safety System and tighten the clamping screw Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Checking the Engines Cooling Air IntakeReplacing the Air Filter Replacing the Fuel Filter Checking Tire PressuresChecking the Parking Brake Deck belt Checking the V-belts1. Clutch pulley Deck belt installationBelt installation EZT beltChecking the Blades Adjusting the Mower Deck To level deck Side-to-sideadjustmentFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Use protective glasses when cleaning and washing Cleaning and WashingCaster Wheels HardwareLUBRICATION LubricationLubrication Schedule Lubricating the Cables IMPORTANT INFORMATION 2. Changing the Oil Filter Checking the oil levelTransmission Trouble Shooting Guide TROUBLE SHOOTING GUIDEWrong fuel type Uneven mowing results Winter Storage ServiceSTORAGE StorageWiring diagram WIRING DIAGRAMSTechnical Data TECHNICAL DATAProductivity EquipmentTorque Specifications TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS U.S. Standard HardwareMetric Standard Hardware CONFORMITY CERTIFICATES Conformity CertificatesUSA requirements SERVICE JOURNAL Service JournalDelivery Service 1. Change engine oil After the First 5-8Hours6.Clean the air cleaner’s pre-filterfoam 25-HourService4.Check battery with cables 5.Check/clean the engine’s cooling air intake3.Change the engine oil 50-HourService1.Perform the 25-hourservice 5.Check/adjust the parking brake3.Change the engine oil filter 100-HourService2.Perform the 50-hourservice 4.Clean/replace the spark plug300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06