Poulan 968999516, 968999507 manual Refueling, Blade switch, Controls

Page 22
5. Refueling

CONTROLS

5. Refueling

Read the Safety Instructions before refueling.

The machine has one fuel tank, just behind the seat. The tank capacity is 3 gallons (11.4 liters).

The engine will run on a minimum of

85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also Technical Data concerning ethanol fuel. Methanol fuel is not allowed.

WARNING!

Gasoline is highly flammable. Observe caution and fill the tank outdoors

(see the safety instructions).

WARNING!

The engine and the exhaust system, become very hot during operation.

Risk for burns if touched.

Allow engine and exhaust system to cool at least two (2) minutes before refueling.

WARNING!

Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to help insure good cold weather starting.

Make sure the full cap is properly tightened and the gasket is not damaged.

6. Blade switch

In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed.

8011-7522

Fuel tank

IMPORTANT INFORMATION

Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.

8011-7502

Blade Switch

English-20

Image 22
Contents 968999516 968999507 EnglishPro 925 ZX Pro 950 ZX Operator´s manualPage Contents OPERATOR’S MANUAL RIDER Z SERIESEnglish-2 Congratulations INTRODUCTIONIntroduction GeneralGood Service Manufacturing NumberSYMBOLS AND DECALS Symbols and DecalsRead Safety Instructions SAFETY INSTRUCTIONSGeneral Operation English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance •Use protective goggles Transport IMPORTANT INFORMATIONCustomer responsibilities Controls CONTROLSControl Locations 1. Motion Control Levers Tracking2. Seat adjustment knobs 3. Fuses4. By pass linkages 6. Blade switch 5. Refueling8. Choke Control 7. Ignition Switch9. Throttle Control 10. Hour Meter 11. Parking BrakeAccessories 12. Cutting height pedalOperation OPERATIONTraining Before Starting Starting the Engine6.Move the throttle to the middle position OPERATION To start an engine with a weak battery Running Operating on hills Mowing Tips Mowing patternsStopping the Engine Moving by Hand Maintenance MAINTENANCEMaintenance Schedule Check/adjust throttle cable Battery Ignition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable and tighten the clamping screwReplacing the Air Filter Checking Tire Pressures Replacing the Fuel FilterChecking the Parking Brake Checking the V-belts Deck beltDeck belt installation 1. Clutch pulleyEZT belt Belt installationChecking the Blades Adjusting the Mower Deck Side-to-sideadjustment To level deckFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Hardware Cleaning and WashingCaster Wheels Use protective glasses when cleaning and washingLubrication LUBRICATIONLubrication Schedule Lubricating the Cables LUBRICATION Checking the oil level 2. Changing the Oil FilterTransmission TROUBLE SHOOTING GUIDE Trouble Shooting GuideWrong fuel type Uneven mowing results Storage ServiceSTORAGE Winter StorageWIRING DIAGRAMS Wiring diagramTECHNICAL DATA Technical DataEquipment ProductivityTorque Specifications U.S. Standard Hardware TORQUE SPECIFICATIONS HEX HEAD CAP SCREWSMetric Standard Hardware Conformity Certificates CONFORMITY CERTIFICATESUSA requirements Service Journal SERVICE JOURNALDelivery Service After the First 5-8Hours 1. Change engine oil5.Check/clean the engine’s cooling air intake 25-HourService4.Check battery with cables 6.Clean the air cleaner’s pre-filterfoam5.Check/adjust the parking brake 50-HourService1.Perform the 25-hourservice 3.Change the engine oil4.Clean/replace the spark plug 100-HourService2.Perform the 50-hourservice 3.Change the engine oil filter300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06