Poulan 968999507, 968999516 manual Lubrication Schedule, General

Page 53

LUBRICATION

LUBRICATION

Lubrication

Lubrication Schedule

			8011-673
	Lubrication schedule		Lubricate with oil can
	12/12 Every year	Lubricate with grease gun	Lubricate with oil can
	1/52 Every Week	Oil change	Level check
	1/365 Every day	Oil change	Level check
	1/365 Every day
		Filter change

General

Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil.

When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulfide grease. For daily use, the machine shall be lubricated twice weekly.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other petroleum products must not be used to clean belts.

English-51

Image 53

Contents Pro 925 ZX Pro 950 ZX English968999516 968999507 Operator´s manualPage OPERATOR’S MANUAL RIDER Z SERIES ContentsEnglish-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSRead General Operation SAFETY INSTRUCTIONSSafety Instructions English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance •Use protective goggles IMPORTANT INFORMATION TransportCustomer responsibilities Control Locations CONTROLSControls Tracking 1. Motion Control Levers3. Fuses 2. Seat adjustment knobs4. By pass linkages 5. Refueling 6. Blade switch9. Throttle Control 7. Ignition Switch8. Choke Control 11. Parking Brake 10. Hour Meter12. Cutting height pedal AccessoriesTraining OPERATIONOperation Starting the Engine Before Starting6.Move the throttle to the middle position IMPORTANT INFORMATION To start an engine with a weak battery Running Operating on hills Mowing patterns Mowing TipsStopping the Engine Moving by Hand Maintenance Schedule MAINTENANCEMaintenance Check/adjust throttle cable Battery Ignition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake and tighten the clamping screwReplacing the Air Filter Checking the Parking Brake Replacing the Fuel FilterChecking Tire Pressures Deck belt Checking the V-belts1. Clutch pulley Deck belt installationBelt installation EZT beltChecking the Blades Adjusting the Mower Deck To level deck Side-to-sideadjustmentFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Caster Wheels Cleaning and WashingHardware Use protective glasses when cleaning and washingLubrication Schedule LUBRICATIONLubrication Lubricating the Cables IMPORTANT INFORMATION 2. Changing the Oil Filter Checking the oil levelTransmission Trouble Shooting Guide TROUBLE SHOOTING GUIDEWrong fuel type Uneven mowing results STORAGE ServiceStorage Winter StorageWiring diagram WIRING DIAGRAMSTechnical Data TECHNICAL DATAProductivity EquipmentTorque Specifications Metric Standard Hardware TORQUE SPECIFICATIONS HEX HEAD CAP SCREWSU.S. Standard Hardware USA requirements CONFORMITY CERTIFICATESConformity Certificates Delivery Service SERVICE JOURNALService Journal 1. Change engine oil After the First 5-8Hours4.Check battery with cables 25-HourService5.Check/clean the engine’s cooling air intake 6.Clean the air cleaner’s pre-filterfoam1.Perform the 25-hourservice 50-HourService5.Check/adjust the parking brake 3.Change the engine oil2.Perform the 50-hourservice 100-HourService4.Clean/replace the spark plug 3.Change the engine oil filter300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06