Poulan 968999516, 968999507 manual Battery, Maintenance

Page 38
Battery

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Recharge at 6-10 amperes for 1 hour

To clean battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Open terminal access doors.

2.Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until shiny.

5.Coat terminals with grease or petroleum jelly

6.Reinstall battery.

Replacing battery

1.Lift Seat and rotate forward.

2.Open terminal access doors.

3.Using two 1/2" wrenches disconnect BLACK battery cable then RED battery cable.

4.Using 7/16" wrench, remove terminal guard.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall terminal guard.

8.First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

9.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

10.Tighten securely.

11.Close terminal access doors.

12.Lower seat.

English-36

Always use protective glasses when handling the battery.

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

CZ-22

1.Terminal guard

2.Terminal access doors Battery installation

WARNING!

Procedures on contact with acid.

External: Rinse with plenty of water.

Internal: Drink large quantities of water or milk. Contact a docotor as soon as possible.

Eyes: Rinse well with plenty of water. Contact a doctor as soon as possible.

Batteries emit explosive gas. Sparks, flames and cigarettes must absolutely not be brought into the vicinity of the battery.

Image 38
Contents 968999516 968999507 EnglishPro 925 ZX Pro 950 ZX Operator´s manualPage Contents OPERATOR’S MANUAL RIDER Z SERIESEnglish-2 Congratulations INTRODUCTIONIntroduction GeneralGood Service Manufacturing NumberSYMBOLS AND DECALS Symbols and DecalsRead General Operation SAFETY INSTRUCTIONSSafety Instructions English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance •Use protective goggles Transport IMPORTANT INFORMATIONCustomer responsibilities Control Locations CONTROLSControls 1. Motion Control Levers Tracking2. Seat adjustment knobs 3. Fuses4. By pass linkages 6. Blade switch 5. Refueling9. Throttle Control 7. Ignition Switch8. Choke Control 10. Hour Meter 11. Parking BrakeAccessories 12. Cutting height pedalTraining OPERATIONOperation Before Starting Starting the Engine6.Move the throttle to the middle position OPERATION To start an engine with a weak battery Running Operating on hills Mowing Tips Mowing patternsStopping the Engine Moving by Hand Maintenance Schedule MAINTENANCEMaintenance Check/adjust throttle cable Battery Ignition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable and tighten the clamping screwReplacing the Air Filter Checking the Parking Brake Replacing the Fuel FilterChecking Tire Pressures Checking the V-belts Deck beltDeck belt installation 1. Clutch pulleyEZT belt Belt installationChecking the Blades Adjusting the Mower Deck Side-to-sideadjustment To level deckFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Hardware Cleaning and WashingCaster Wheels Use protective glasses when cleaning and washingLubrication Schedule LUBRICATIONLubrication Lubricating the Cables LUBRICATION Checking the oil level 2. Changing the Oil FilterTransmission TROUBLE SHOOTING GUIDE Trouble Shooting GuideWrong fuel type Uneven mowing results Storage ServiceSTORAGE Winter StorageWIRING DIAGRAMS Wiring diagramTECHNICAL DATA Technical DataEquipment ProductivityTorque Specifications Metric Standard Hardware TORQUE SPECIFICATIONS HEX HEAD CAP SCREWSU.S. Standard Hardware USA requirements CONFORMITY CERTIFICATESConformity Certificates Delivery Service SERVICE JOURNALService Journal After the First 5-8Hours 1. Change engine oil5.Check/clean the engine’s cooling air intake 25-HourService4.Check battery with cables 6.Clean the air cleaner’s pre-filterfoam5.Check/adjust the parking brake 50-HourService1.Perform the 25-hourservice 3.Change the engine oil4.Clean/replace the spark plug 100-HourService2.Perform the 50-hourservice 3.Change the engine oil filter300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06