Poulan 968999507, 968999516 manual Maintenance, Deck belt installation, Clutch pulley

Page 45

Deck belt installation

MAINTENANCE

Deck belt installation

NOTE: For ease in installing the deck belt, refer to the routing decal on bottom of seat.

•Wrap the deck belt around the electric clutch pulley that is located on the engine shaft.

•Route the belt forward between the EZT (E-Series Zeroturn Transaxles) and up onto the deck.

•Place belt around spring loaded idler pulley, between the pulley and guide. Secure bolt and nut.

•Starting on the right hand side of the deck, wrap the belt around the stationary idler pulley, the right mandrel housing, then around to the left mandrel housing.

•Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt.

•Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed.

•Replace belt shields on both mandrel housings and secure with fasteners.

1

1. Clutch pulley

Belt routing, deck belt

English-43

Image 45

Contents Pro 925 ZX Pro 950 ZX English968999516 968999507 Operator´s manualPage OPERATOR’S MANUAL RIDER Z SERIES ContentsEnglish-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSRead SAFETY INSTRUCTIONS Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance •Use protective goggles IMPORTANT INFORMATION TransportCustomer responsibilities CONTROLS ControlsControl Locations Tracking 1. Motion Control Levers3. Fuses 2. Seat adjustment knobs4. By pass linkages 5. Refueling 6. Blade switch7. Ignition Switch 8. Choke Control9. Throttle Control 11. Parking Brake 10. Hour Meter12. Cutting height pedal AccessoriesOPERATION OperationTraining Starting the Engine Before Starting6.Move the throttle to the middle position IMPORTANT INFORMATION To start an engine with a weak battery Running Operating on hills Mowing patterns Mowing TipsStopping the Engine Moving by Hand MAINTENANCE MaintenanceMaintenance Schedule Check/adjust throttle cable Battery Ignition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake and tighten the clamping screwReplacing the Air Filter Replacing the Fuel Filter Checking Tire PressuresChecking the Parking Brake Deck belt Checking the V-belts1. Clutch pulley Deck belt installationBelt installation EZT beltChecking the Blades Adjusting the Mower Deck To level deck Side-to-sideadjustmentFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Caster Wheels Cleaning and WashingHardware Use protective glasses when cleaning and washingLUBRICATION LubricationLubrication Schedule Lubricating the Cables IMPORTANT INFORMATION 2. Changing the Oil Filter Checking the oil levelTransmission Trouble Shooting Guide TROUBLE SHOOTING GUIDEWrong fuel type Uneven mowing results STORAGE ServiceStorage Winter StorageWiring diagram WIRING DIAGRAMSTechnical Data TECHNICAL DATAProductivity EquipmentTorque Specifications TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS U.S. Standard HardwareMetric Standard Hardware CONFORMITY CERTIFICATES Conformity CertificatesUSA requirements SERVICE JOURNAL Service JournalDelivery Service 1. Change engine oil After the First 5-8Hours4.Check battery with cables 25-HourService5.Check/clean the engine’s cooling air intake 6.Clean the air cleaner’s pre-filterfoam1.Perform the 25-hourservice 50-HourService5.Check/adjust the parking brake 3.Change the engine oil2.Perform the 50-hourservice 100-HourService4.Clean/replace the spark plug 3.Change the engine oil filter300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06