Poulan 968999507, 968999516 manual Safety Instructions, General Operation

Page 9
SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Safety Instructions

These instructions are for your safety. Read them carefully.

WARNING!

This symbol means that important safety instructions need to be emphasized. It concerns your safety.

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

General Operation

Read, understand, and follow all instructions on the machine and in the manual before starting.

Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

Only allow responsible adults, who are familiar with the instructions, to operate the machine.

Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.

Be sure the area is clear of bystanders and pets before operating. Stop machine if anyone enters the area.

Never carry passengers. The machine is only intended for use by one person.

Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.

Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.

Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working

Slow down before turning.

Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.

8011-512

Read the operator’s manual before starting the machine

8011-513

Clear the area of objects before mowing

8011-520

Never take passengers

English-7

Image 9
Contents Pro 925 ZX Pro 950 ZX English968999516 968999507 Operator´s manualPage OPERATOR’S MANUAL RIDER Z SERIES ContentsEnglish-2 Introduction INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceSymbols and Decals SYMBOLS AND DECALSRead SAFETY INSTRUCTIONS Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance •Use protective goggles IMPORTANT INFORMATION TransportCustomer responsibilities CONTROLS ControlsControl Locations Tracking 1. Motion Control Levers3. Fuses 2. Seat adjustment knobs4. By pass linkages 5. Refueling 6. Blade switch7. Ignition Switch 8. Choke Control9. Throttle Control 11. Parking Brake 10. Hour Meter12. Cutting height pedal AccessoriesOPERATION OperationTraining Starting the Engine Before Starting6.Move the throttle to the middle position IMPORTANT INFORMATION To start an engine with a weak battery Running Operating on hills Mowing patterns Mowing TipsStopping the Engine Moving by Hand MAINTENANCE MaintenanceMaintenance Schedule Check/adjust throttle cable Battery Ignition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake and tighten the clamping screwReplacing the Air Filter Replacing the Fuel Filter Checking Tire PressuresChecking the Parking Brake Deck belt Checking the V-belts1. Clutch pulley Deck belt installationBelt installation EZT beltChecking the Blades Adjusting the Mower Deck To level deck Side-to-sideadjustmentFront-to-backadjustment IMPORTANT INFORMATION To adjust anti-scalprollers Caster Wheels Cleaning and WashingHardware Use protective glasses when cleaning and washingLUBRICATION LubricationLubrication Schedule Lubricating the Cables IMPORTANT INFORMATION 2. Changing the Oil Filter Checking the oil levelTransmission Trouble Shooting Guide TROUBLE SHOOTING GUIDEWrong fuel type Uneven mowing results STORAGE ServiceStorage Winter StorageWiring diagram WIRING DIAGRAMSTechnical Data TECHNICAL DATAProductivity EquipmentTorque Specifications TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS U.S. Standard HardwareMetric Standard Hardware CONFORMITY CERTIFICATES Conformity CertificatesUSA requirements SERVICE JOURNAL Service JournalDelivery Service 1. Change engine oil After the First 5-8Hours4.Check battery with cables 25-HourService5.Check/clean the engine’s cooling air intake 6.Clean the air cleaner’s pre-filterfoam1.Perform the 25-hourservice 50-HourService5.Check/adjust the parking brake 3.Change the engine oil2.Perform the 50-hourservice 100-HourService4.Clean/replace the spark plug 3.Change the engine oil filter300-HourService At Least Once Each Year English-73 English-74 English-75 Page Page 113920Rir07/11/06